Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See “Using the Controls.”

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

IMPORTANT:

If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

All installations must meet local plumbing code requirements.

Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches, ¹⁄₄" nut driver and drill bit, cordless drill.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

(on some models)

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ¹⁄₂" to 1¹⁄₄" (1.27 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

Make sure it is a cold water pipe.

Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you will need. Measure from the connection on lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a grounded drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

4

Page 4
Image 4
Estate 2316077B warranty Electrical Requirements, Water Supply Requirements, Connect the Water Supply

2316077B specifications

Estate 2316077B is a groundbreaking development that has transformed the landscape of modern living. This estate is designed not just as a place to reside but as a harmonious integration of sustainability, technology, and lifestyle amenities. One of its main features is the emphasis on eco-friendly architecture, which incorporates renewable resources, energy-efficient designs, and sustainable materials. The buildings are constructed with advanced insulation techniques that minimize energy loss, lowering utility costs for residents.

The estate boasts smart home technologies that redefine convenience and security. Every unit is equipped with a comprehensive home automation system that allows residents to control lighting, heating, and security features from their smartphones or tablets. This integration of technology not only enhances comfort but also promotes energy efficiency, as systems can be optimized for usage patterns. Additionally, advanced security measures, including biometric entry systems and 24/7 monitoring, provide residents with peace of mind.

Another notable characteristic of Estate 2316077B is its commitment to community and wellness. The estate includes lush green spaces, walking trails, and recreational areas that encourage outdoor activities and social interactions. There are dedicated zones for gardening, playgrounds for children, and facilities for fitness and relaxation. Together, these features foster a strong sense of community among residents, making the estate a desirable place to live.

The technological amenities extend beyond smart home features. Internet connectivity is robust, with high-speed fiber-optic networks available throughout the estate. This ensures that residents can easily work from home, stream entertainment, and engage in online learning without interruptions.

Moreover, Estate 2316077B is strategically located near essential services such as schools, shopping centers, and healthcare facilities. Its accessibility to public transportation further enhances its appeal, making commuting convenient for those who work in nearby urban centers.

In summary, Estate 2316077B represents a forward-thinking approach to modern living, blending innovative technologies, sustainable practices, and community-centric design. Its focus on providing a high-quality lifestyle while prioritizing environmental responsibility makes it a premier choice for discerning homeowners. As urban living continues to evolve, developments like Estate 2316077B set a new standard for what residents can expect from their living environments.