Eureka! Tents N!ergy Portable Canopy important safety instructions Assembly Instructions

￿g.11

			Raise the Perimeter and
		ASSEMBLY INSTRUCTIONS	Roof Rafters:
			• At each corner, lift the
		N!ERGY PORTABLE CANOPY
			bottom section of the
			perimeter rafter until the
Component List: 1 Canopy Top, 1 Frame Assembly, 1 Carry Bag			lock button on the leg
			clicks into its seat in the
w/Wheels, 1 Pre-Installed Wiring Harness w/ Switch, 4 Nailhead
			collar. See ￿g. 4 & 5. Take
Stakes, 4 Guy Out Skewers, 4 Attached Guy Out Cords
			care that the collar truly
NOTE: Do not drop carry bag. Do not bounce the bag on its end to get
			captures the button,
the frame out. These actions may damage the electrical components.			otherwise the roof will
Although it is possible to raise this structure by yourself; it is much easier			slide back down.	￿g.4
and faster if you have help.			• Continue with the rest of
Expand the Frame:			the perimeter rafters
			until all corners are
• Open the carry bag, remove the frame and top. Lay the top aside and			locked in place and the
stand the frame up, near its final location			roof is extended as
• With one person at A and another at B, lift the poles and step back to			shown in ￿g. 6
pull the legs out and away from the center. See fig. 1. Move to C and D
and again lift and pull the	B	D	A
legs out and away. Work
back and forth between		C
AB and CD, until the
frame is extended as
shown in ￿g. 2
• If you are working alone,
pull the frame apart as
best you can and then
drive a nailhead stake
through the hole in the
baseplate of one of the			Attach the Canopy Top to the Frame:
legs. See ￿g. 3. Work your
way from corner, pulling			• Lay the fabric on the ground with the top facing
out and away from the			up and square to the frame.
staked leg			• Grasp the two canopy corners closest to the frame
• Continue until the frame		￿g.1	and drag them up and over the roof to the frame
is extended as shown in			corners on the opposite side. Take care that the
￿g. 2			electrical plugs do not get caught on the frame as

you tug the canopy

• At each corner, fit the fabric snug to the frame. Align the guy gusset to the top of the frame and at a 45˚ angle from the leg. See fig. 7

• Move inside, under the canopy. Wrap each pair of Velcro® hook pads from the inside corners of the

￿g.5

￿g.6

￿g.7

Raise the Legs:

•Station one person at each leg on one side of the frame.

Lift the legs and

press the button on the black collar to release the inside section. See ￿g. 10. Allow the inside

sections to fall to one of the three lock points. Make sure that the legs are the

same height and that they are locked in￿g.10 place. See ￿g.11

• Repeat with the remaining two legs

Secure the Structure to the Ground:

•Drive a nailhead stake through the holes in the baseplates at the bottom of the legs. See fig. 12

•Use the skewers to stake

the guyout cords and adjust tension with the attached sliders. See ￿g. 13

￿g.12 ￿g.13

YOUR CANOPY IS READY!

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See ￿g 14

canopy to the loops near the top of the corner poles. See ￿g. 8

• Attach all remaining Velcro® tabs to the perimeter and roof rafters. See fig. 9

￿g.2

￿g.3 ￿g.9

￿g.8

Take Down: Pull up all stakes. Release the canopy’s hook & loop straps and remove from the frame. You may leave the wire harness in place. Collapse all poles and stow. Fold the canopy onto itself, roll up.and stow.

Read the important safety instructions on the reverse side.

blue

green

￿g.14

Rev B 4.09