Assembly Instructions for the N!ergy 9 Tent
Component List:
1 Wired Tent Body, 2 Tent Poles, 1 Tent Fly, 2 Fly Poles, 1 Stake Bag w/Stakes, 1 Pole Bag, 4 Guy Ropes and 1 Carry Bag,
NOTE:
•Although it is possible to pitch this tent alone, it is faster/easier with two people.
•Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to get the tent out. These actions may cut the shockcord and/or damage the pole ends.
•The N!ergy series tents are
1.Unroll and unfold the tent on the ground. Separate the rest of the components and place to one side. Open the door before pitching the tent. Do not stake the tent down (however, in windy conditions, stake down one corner that faces into the wind). See fig 1.
4.Raise up the tent poles. Step inside the tent door and attach the peak of the tent to the center of the top pole with the web clip. Attach the remaining roof clips. See fig 5.
fig 5
7.Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front of the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to side down the center of the fly forming an X. Secure the fly to the poles by wrapping the hook & loop fastener around the fly poles. See fig 9, 10 and 11.
fig 11
8.Attach the fly to the tent. Turn the fly assembly over and align it so that the poles point out over the doors. Grasp the corners of the of the fly and drag them up and over the roof to completely cover the tent. (This is much easier with two people.)
At the corners of the tent, reach under the fly and attach the hook & loop straps to the tent poles, securing the fly in place. See fig 12.
At the bottom/corners of the tent, attach the shockcorded
fig 9
fig 10
fig 12
Fly
Poles
Tent
Poles
fig 2
fig 1
2.Assemble the shockcorded poles. Keep the end sections from snapping together, as this can damage the ends. Make certain each plain end has been properly seated into the metal ferrule. See fig 2.
5.Attach the side clips to the poles to create a freestanding tent. Place it in the desired location. See fig 6.
6.Stake the tent down through the corner web loops. Stake opposite corners while applying tension to smooth the floor wrinkles, squaring the tent as you work. Also, stake out the floor beckets at the center of each side and at the back of the tent. See fig 7 & 8.
fig 7
fig 6
fig 13.
At the bottom/sides of the fly, pull out and stake down the web loops.
9. Tie a guy rope to each of the 4 rings attached to the fly and stake out.
Adjust tension
with the
See fig 14 & 15.
fig 15
Your tent is now ready.
fig 13
fig 14
3.Place a corner pin into the end of one of the poles. At the opposite end, with the pole in one hand and a pin & ring in the other, feed the pole up, bending it evenly along its length to create an arc. Place the pin into the end of the pole to maintain tension. Repeat with the other pole. See fig 3 & 4.
fig 3
fig 8
fig 4
E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16.
E! Power Port: Open zipper and run extension cord through opening.
Close zipper so that it rests next to the extension cord. Make sure |
|
|
the zipper cover is not twisted or tucked. The cover must lay flat |
|
|
against the outside of the tent to keep out rain. |
| blue |
Accessories: E! Power Fan/Light, E! Power Reading Light and an |
| green |
E! Power 12v Adapter Cord. |
|
|
Sweep Out: Inside, at the bottom of the door is a |
| fig 16 |
Pull this loop to the outside and stake it down to provide a ready exit |
|
|
for floor sweepings. See fig 17. |
| |
Take Down: Pull up all stakes. Release the fly’s hook & loop straps. Remove fly. |
| |
Remove fly poles. Remove clips from tent poles and pull poles off of the pins. |
| |
Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it | fig 17 | |
on tent. Roll up both towards the open door and stow. | ||
Read the important safety instructions on the reverse side. |
| |
|
REV. A 11.06