OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS cont.
NOTE: Always remove the power plug from the wall outlet before assembling or removing accessories.
1.Add 6 to 8 cups of water to the tank.
2.Attach the flexible hose to the suction hole.
3.Attach one of the extension tubes to the hand grip of the flexible hose. Insert the hand grip into the wider end of the extension tube and turn to tighten the connection.
4.Attach the other extension tubes to the first one and turn to tighten the connection.
5.Attach the desired accessory (brush with squeegee, air driven turbo brush or floor to carpet brush) to the narrow end of the extension tube.
Assembling the Base Casters
The casters for the base on your new Bagless Water Filtration Vacuum are packed and shipped unassembled. To assemble the caster to the base, simply insert the caster stem into one of the four (4) holes in the base and push downward with the palm of your hand. (See illustration below.) Repeat for the next three (3) casters.
Your CW240 Water Filtration Vacuum may also be used as a wet
NOTE: The air driven turbo brush may not be used for wet
WARNING: Water level MUST NEVER exceed the "Max" level indicated on the water tank. Empty tank when water level reaches "MAX" indicator. If water is seen to be coming from the exhaust - immediately turn the unit off and unplug from electrical outlet. Empty water tank and clean. Refill water tank with clean water to the "MIN" level, then plug unit back in and continue working.
Using Your Bagless Water Filtration Vacuum
IMPORTANT: DO NOT operate this vacuum when water level is below the "Min" line on the water tank.
1. Unwrap the power cord to the |
desired length. |
2. Insert plug into electrical outlet. |
3. Turn the "On/Off" Switch to the "On" |
position. |
4. The speed control knob can be used |
to adjust the suction. The manual |
variable suction control on the hand |
grip can be used to further reduce |
the suction. |
5. Keep the flat space between the |
floor brush and floor surface, hand |
grip and extension tube and move |
Using the Deluxe and Compact Air Driven Turbo Brushes
1.Turn off the vacuum and unplug from wall outlet.
2.Attach the Air Driven Turbo Brush to the extension tube.
3.
4.The Deluxe Air Driven Turbo Brush is adjustable for carpet nap. The Compact Turbo Brush is not. To adjust for high pile carpet, move the slide control on top of the brush housing as shown in Fig. 1.
5.For low nap adjust the slide control as shown in fig. 2.
IMPORTANT: Do not use the Air Driven Turbo Brush for wet
Fig. 2
Fig. 1
Slide | Slide |
For high pile carpet | For low nap carpet |
Cleaning the Compact Air Driven Turbo Brush
Locking Latch
Tilt
Upwards
Turbine
1.Slide locking latch forward then tilt the top housing of the brush upwards. The top housing is hinged and will tilt up approximately 45°only.
2.Inspect turbine wheel and air passage for debris and/or blockage. Remove debris if present.
3.Inspect the rotating brush for
4.Once clean, close the top cover of the turbo brush and slide the locking latch toward the rear of the brush to lock.
WARNING: These air driven turbo brushes rotate with the force of the suction power. As the water tank fills with dirt, the suction power will reduce and the air driven turbo brushes will slow down. If this happens, empty the water tank and verify that no threads or hairs have accumulated on the beater brushes which can also reduce beater brush rotation speed.
the vacuum cleaner up and down. |
6. When finished using the unit, unplug |
from electrical outlet and wrap the |
power cord around the top of the |
unit. |
Compact Air Driven Turbo Brush
WARNING: The beater brush of this floor attachment rotates very fast. To avoid injury, DO NOT TOUCH the beater brush with fingers while the brush is rotating.
3 | 4 |