OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Warning: Always unplug from electrical outlet before opening the dust cup (container).
Note: Dust cup filter must be used when operating the hand vacuum.
5.To use the hand vacuum with the extension tube, push the narrower end of the tube into the suction hole, then attach the desired accessory to the other end of the tube, as shown below.
Using the Convertible Brush
Note: The convertible brush with removable bristles can be used with the hose, the extension tube or with the unit alone.
For vacuuming high, hard to reach
Cleaning Air Driven Turbo Brush
Locking Latch
Tilt
Upwards
Using The Unit As A Hand Vacuum
1.To open the dust cup (container), lift button and pull out the dust cup. Verify that the dust cup filter is inside, then attach the dust cup (container) to the hand vacuum.
2.To use the hand vacuum with the shoulder strap, attach it to the unit as shown below.
3.To attach the cleaning brush or crevice tool to the Hand Vacuum, push accessory into the suction hole, as shown below.
4.To use the hand vacuum with the flexible hose, push the end of the hose into the suction hole,
then attach the desired accessory to the other end of the flexible hose, as shown below.
6.To use the hand vacuum with both the flexible hose and the extension tube, first insert the flexible hose into the hand vacuum and then push the narrower end of the tube into the other end of the flexible hose. Then attach the desired accessory to the other end of the tube, as shown below.
How To Operate Your Hand Vacuum
1.Hold the hand vacuum firmly in your hand by the Handle.
2.Push the On/Off Power Switch to “On” position.
3.Start vacuuming.
CAUTION: The hand vacuum is a Very powerful unit. Make sure that you hold it firmly, otherwise it can slip out of your hand and cause injury.
places such as ceilings, curtains/drapes, etc., use the convertible brush with removable bristles as follows:
1.Insert the convertible brush to the hose alone or with the extension tube attached to the hose.
2.If you need a brush action, slide on the removable bristle brush onto the deluxe brush. (See illustration below)
Slide
Using the Unit With Air Driven Turbo Brush
1.Slide the narrow end of the extension tube into the air driven turbo brush.
2.Slide the wide end of the extension tube onto the round end of the deluxe hose with suction control.
3.Slide the round side of the deluxe hose with suction control into the suction hole of the vacuum unit.
4.Attach the shoulder strap to the vacuum and hang it from your shoulder.
5.You can now proceed to vacuum your carpet or hard floor.
CAUTION: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could get damaged.
Turbine
1.Slide locking latch forward then tilt the top housing of the brush upwards. The top housing is hinged and will tilt up approximately 45° only.
2.Inspect turbine wheel and air passage for debris and/or blockage. Remove debris if present.
3.Inspect the rotating brush for
4.Once clean, close the top cover of the turbo brush and slide the locking latch toward the rear of the brush to lock.
IMPORTANT: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:
•Push the On/Off button once.
•Disconnect the plug from the power source.
•Check the source of overheating problem. (i.e. clogged hose or filter)
•If clogged hose or filter is found, unclog the hose and replace the filters.
•Wait at least 45 minutes before attempting to reuse the vacuum.
•After unit has cooled down for 45 minutes, plug in the cleaner and push the On/Off button. The vacuum should start again.
•If the vacuum still does not start, please contact Customer Service at 1 (800)
4
5
