Euro-Pro EP722 Cleaning & Changing the HEPA Dust Cup Filter, Power Cord, Operating Instructions

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Crevice Tool, Upholstery and Dusting Brush

1.Crevice Tool

For radiators, crevices, corners, baseboards and between cushions.

2.Dusting Brush

The dusting brush is used for the furniture, venetian blinds, books, lamp shades and shelves.

3.Upholstery Brush

The dusting brush is used for the furniture.

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, dust cup filter,changing the filters or performing maintenance/trouble shooting checks.

Note: Before using the appliance, unwind a sufficient length of cable and Insert the plug into the wall socket. A yellow mark on the power cord shows the ideal cable length. Don’t pull the power cord beyond the red mark.

Power Cord

Your vacuum cleaner includes a power cord, which is automatically retractable. To extend your power cord, pull from rear and extend to desired length. When cleaning is finished, first switch off power and disconnect plug from electrical outlet. Then press on cord rewind button. If the cord does not fully retract, pull it out again and then press on cord rewind button.

1.Insert the power plug into the wall outlet.

2.Press the Power On/Off Switch to activate the vacuum cleaner.

Power On/Off Button

3.To rewind the power cord, press the cable rewind button with one hand and guide the power cord with the other hand to ensure that it does not whip

causing damage.

Cord Rewind

Yellow

Red Symbol

Symbol

Warning: Hold the plug when rewinding the cord. Do not allow the cord to whip when rewinding.

Cleaning Air Driven Turbo Brush

Locking Latch

Tilt

Upwards

Turbine

1.Slide locking latch forward then tilt the top housing of the brush upwards. The top housing is hinged and will tilt up approximately 45° only.

2.Inspect turbine wheel and air passage for debris and/or blockage. Remove debris if present.

3.Inspect the rotating brush for built-up hair or string. If present, remove by carefully cutting with scissors. Avoid damaging or cutting bristles.

4.Once clean, close the top cover of the turbo brush and slide the locking latch toward the rear of the brush to lock.

Cleaning & Changing the HEPA Dust Cup Filter

Warning: Always unplug the unit from electrical outlet before opening the Dust Cup (container).

Important: Do NOT use the HEPA filter cartridge without the debris screen in place.

Warning: After each Use - Always remove the Filter Debris Screen from the HEPA Dust Cup Filter, then vigorously “TapClean” HEPA Filter until no more dust can be removed.

IMPORTANT, Please Note : The “TapClean” HEPA Dust Cup Filter & Debris Screen will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact it stops 99.97% of all particles as small as

0.3microns - many times smaller than a human hair!!! Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate, inside the white filter folds, many fine dust particles that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. This can cause the motor to overheat and the re- settable thermostat to trip. (Should this happen turn off the switch, unplug the unit and allow unit to cool down. Clean the HEPA Filter and Debris Screen as described in this section, then reconnect unit and proceed with vacuuming.)

1.Push the Power On/Off switch to the OFF position to disconnect the power.

2.Remove the flexible hose.

3.Remove the dust cup by lifting the dust cup handle. See illustration below.

Dust Cup Handle

4.Take the HEPA dust cup filter out of the dust cup, do not let dust fall out of dust cup.

5.Take the dust cup and dispose of the dust inside.

6.Separate the debris screen from the HEPA filter cartridge by grasping the debris screen with one hand and the filter frame with the other and pull apart.

HEPA Filter Debris Screen

7.Vigorously “TapClean” the HEPA Dust

Cup Filter on a hard surface until no more dust is observed falling out from between the pleats of the filter. Please note

that on the under side of the HEPA dust cup filter there is a small brush which you can use to brush out the pleats of the filter.

8.“TapClean” the Debris Screen or rinse under a faucet until clean.

Remember that the Debris Screen must be completely dry before reinstalling in the vacuum.

5

6