GETTING TO KNOW YOUR QUAD BLADE FOOD
OPERATING INSTRUCTIONS
PROCESSING CENTER
1. | Processor Body | 17. | Juice Extractor Filter |
2. | Safety Cover | 18. | Whipping Attachment |
3. | Safety Cover/Blender Location | 19. | Citrus Juicer Filter |
4. | On/Off Speed Control Dial | 20. | Juice Reamer |
5. | Turbo/Pulse Button | 21. | Main Chopping Blade |
6. | Drive Shaft | 22. | Double Chopping Blade |
7. | Storage Compartment | 23. | Chopping Blade Protective Cover |
8. | Blender Jar | 24. | Blade Holder |
9. | Blender Lid | 25. | French Fry Disk Assembly |
10. | Measuring Cap | 26. | Dough Blade |
11. | Processor Bowl | 27. | Thick Slicing Blade |
12. | Spindle | 28. | Thin Slicing Blade |
13. | Processor Lid | 29. | Fine Chopping Blade |
14. | Food Pusher | 30. | Coarse Chopping Blade |
15. | Juice Extractor Lid | 31. | Spatula |
16. | Juice Extractor Pusher |
|
|
Technical Specifications
Voltage: | 120V., 60Hz. | |
Power: | 800 Watts | |
Food Processor Capacity: | 6 | Cups (1.5 Liters) |
Blender Capacity: | 7 | Cups (1.75 Liters) |
Speed Control Dial
The food processor and blender speed control dial has speeds settings as follows: (Fig. 1)
Pulse/Turbo
The speed can be |
|
adjusted while the |
|
food processor is |
|
in use. | Fig. 1 |
Use of the Pulse/Turbo button allows greater control over the texture of the food being processed. Use "Pulse" when the unit is in the "Off" position. Use "Turbo" when the unit is in the "On" position and you need a burst of power. Please note that the "Pulse" and "Turbo" is only intended to be used for short "bursts" of processing.
Operating the Food Processor
Setting up:
1.CAUTION: Make sure that the unit is unplugged from the power source and the the Speed control dial is in the "Off" position before inserting or removing any attachments and before cleaning.
2.Fit the safety cover into the food processor body and turn counterclockwise firmly until it “clicks” into place (the arrows will now be lined up). IMPORTANT THE FOOD
PROCESSOR WILL NOT OPERATE WITHOUT THE SAFETY COVER IN PLACE.
3.Place the food processor bowl onto the processor body.
There is no need to turn the bowl. (Fig. 2)
4.When fitted correctly, the handle will be to the right of the
assembly, and the ridge on the base
of the bowl will fit into the slot at the back of the processor body.
(Fig. 3 & Fig. 4)
Fig. 3 | Fig. 4 |
5.Fit the spindle onto the motor shaft and the appropriate attachments onto the spindle. (Fig. 5)
WARNING
TO REDUCE THE RISK OF INJURY, NEVER PLACE THE CUTTING BLADE ON THE BASE WITHOUT FIRST PUTTING THE BOWL PROPERLY IN PLACE.
Fig. 5
6. Holding the | Fig. 6 |
processor lid |
|
by the feed tube, |
|
fit the lid by |
|
rotating |
|
counterclockwise. |
|
(Fig. 6) |
|
7.Ensure that the lid tab has “clicked” into place and the arrows are lined up. (Fig. 8)
8.Plug the processor Fig. 7 and switch on.
If the processor does not come on, check that the machine cover and processor lid are
both correctly fitted. Fig8 (Fig. 8)
For safety, always |
|
use the food |
|
pusher when |
|
putting food into |
|
the feeder tube. |
|
Never feed by |
|
hand. (Fig. 9) | Fig9 |
|
WARNING: Always remove the blender and fit the safety cover into the processor body when using the processor.
3 | 4 |
