OPERATING INSTRUCTIONS GETTING TO KNOW YOUR MINI CANISTER VACUUM
1. To open the Dust Cup (container),
push the dust cup release button
and pull out the Dust Cup
(container ).
IMPORTANT, Please Note : The
“TapClean” Rinseable HEPA Dust Cup
Filter & Debris Screen will stop most of
the tiniest dust particles from re-entering
the air you breathe. In fact it stops
99.97% of all particles as small as 0.3
microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust
Cup Filter will quickly accumulate, inside
the white filter folds, many fine dust
particles that are difficult to see but which
will eventually block or reduce your
suction power - if not cleaned properly.
Clean the HEPA Filter and Debris Screen
after each use as described in this
section.
3. To remove the
HEPA filter from
the dust cup
container hold the dust
cup in one hand and
insert one finger of
your other hand into
the inlet hole on
the dust cup cover
and pull it up.
2. Press the dust
cup trap door
release button
to empty the
dirt into a
trash can.
4. When the HEPA Filter
assembly is removed
from the dust cup, pull
off the debris screen
first. Then to remove
the HEPA Filter from
the Dust Cup Cover,
hold the HEPA filter
with one hand and
with the other hand
pull the dust cup cover
up.
Turbine
Tilt
Upwards
Locking Latch
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1.Remove the turbo brush from the hose
or telescopic extension tube.
2.Slide locking latch forward then tilt the
top housing of the brush upwards. The
top housing is hinged and will tilt up
approximately 45° only.
3.There may be some dust, lint, hair, etc
on the turbine wheel. Remove as much
of this as possible.
4.You may also use the unit’s hose with
crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.
5.Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call
Customer Service for help.
6.Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.

Cleaning Air Driven Turbo Brush

IMPORTANT:In order to ensure that
maximum air suction is maintained,
empty the dust cup frequently and shake
out the HEPA filter and Debris Screen at
the same time. Ensure that the rotating
brush is kept free of hair and string which
may accumulate and decrease brush
performance.
19
11. Dust Cup Handle
12. Flexible Hose
13. Floor Brush
14. Deluxe Brush With Removable
Bristles
15. Extension Tubes (x3)
16. Crevice Tool
17. HEPA Dust Cup Filter
18. Debris Screen
19. Air Driven Turbo Brush
20. Shoulder Strap
1. On/Off Power Switch
2. Hose Release Button
3. Dust Cup Release Button
4. Dust Cup (Container)
5. Caddy
6. Exhaust Filter Cover
7. Main Unit
8. Intelli-Sense Filter MonitorTM
9. Shoulder Strap Attachment Points
10.Dust Cup Trap Door Release
Button

Cleaning & Changing the HEPA

Dust Cup Filter

WARNING: Always unplug the unit from
electrical outlet before opening the Dust
Cup (container).
IMPORTANT: Do NOT use the HEPA
dust cup filter without the debris screen in
place.
WARNING:After each Use - Always
remove the Filter Debris Screen from the
HEPA Dust Cup Filter, then vigorously
“TapClean” HEPA Filter until no more
dust can be removed.

Illustrations may differ from actual product.

Technical Specifications
Voltage: 120V., 60Hz.
Power: 8.33 Amps
3
6