Euro-Pro V1505 owner manual Operating Instructions, Using The Unit As a Hand Vacuum

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS cont.

Warning: Always unplug from electrical outlet before opening the dust cup (container).

Note: HEPA dust cup filter must be used when operating the hand vacuum.

Using The Unit As A Hand Vacuum

1.To open the dust cup (container), push the dust cup release button and pull out the dust cup. Verify that the HEPA dust cup filter is inside, then re-attach the dust cup (container) to the hand vacuum.

2.To use the Hand Vacuum with the shoulder strap, attach it to the unit as shown below.

3.To attach the crevice tool or oval brush to the Hand Vacuum, push brush into the suction hole, as shown below.

4.To use the flexible hose, push the smaller end of the hose into the suction hole, then attach the desired accessory to the other end of the flexible hose, as shown below.

How To Operate Your Hand Vacuum

1.Hold the hand vacuum firmly in your hand by the Handle.

2.Push the On/Off Power Switch to “On” position.

3.Start vacuuming.

CAUTION: The Hand Vacuum is a very powerful unit. Make sure that you hold it firmly, otherwise it can slip out of your hand and cause injury.

Intelli-SenseTM

Filter Monitor

When the Intelli-SenseTMFilter Monitor lights up, it means that the dust cup is full or filter needs cleaning. You must empty the dust from the dust cup and clean the HEPA dust cup filter right away.

Cleaning & Changing the HEPA Dust Cup Filter

Warning: Always unplug the unit from electrical outlet before opening the Dust Cup (container).

Important: Do NOT use the HEPA filter cartridge without the debris screen in place.

Warning: After each Use - Always remove the Filter Debris Screen from the HEPA Dust Cup Filter, then vigorously “TapClean” HEPA Filter until no more dust can be removed.

IMPORTANT, Please Note : The “TapClean” HEPA Dust Cup Filter & Debris Screen will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact it stops 99.97% of all particles as small as

0.3microns - many times smaller than a human hair!!! Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate, inside the white filter folds, many fine dust particles that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. This can cause the motor to overheat and the re- settable thermostat to trip. (Should this happen turn off the switch, unplug the unit and allow unit to cool down. Clean the HEPA Filter and Debris Screen as described in this section, then reconnect unit and proceed with vacuuming.)

1. To open the Dust Cup (container), push the dust cup release button and detach the Dust Cup (container). (Fig. 1)

2. Pull out the HEPA Dust Cup Filter or cloth dust cup filter. (Fig. 2)

Fig. 1 Fig.2

3.	Empty the dust from the Dust Cup
	(container).
4.	Separate the debris screen from the
	HEPA filter cartridge by grasping the
	debris screen with one hand and the

Debris
Screen	HEPA Filter
Fig. 3
5. Vigorously “TapClean”	Fig. 4
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (Fig. 4)
6. “TapClean” the Debris
Screen or rinse under
a faucet until clean.
(Fig. 5) Remember	Fig. 5
that the Debris Screen
must be completely
dry before reinstalling	Debris
in the vacuum.
	Screen

7.Replace the Debris Screen on the HEPA Dust Cup Filter and reinstall filter assembly in the vacuum. (not shown)

PLEASE NOTE: The white pleated filter material in the HEPA Dust Cup Filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA

Dust Cup Filter
is properly
"TapCleaned”	Fig. A
after each use	Wash once a
and suction	month or when
does not return	suction
	appears
to 100%, then	reduced.
we suggest that	Warning: Allow 24
the HEPA filter	hours for drying before
be “TapCleaned”	replacing in unit.
vigorously until no

more dust can be removed, then rinsed under the faucet and allowed to dry for 24 hours before refitting into the vacuum. (Fig. A) Wash once a month or when suction appears reduced.

3

filter frame with the other and pull

apart. (fig. 3)

4

CAUTION: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.