Euro-Pro VPW49HA Attaching The Wheels To Pressure Washer, Attaching The Handle To Pressure Washer

Assembling the Pressure Washer

OPERATING INSTRUCTIONS

Attaching The Wheels To The

Pressure Washer

1.Carefully take all the parts out of the packaging container and place together on a flat, stable surface.

2.Insert the wheels onto the wheel axle and push in the wheel lock to lock the wheels in place. (Fig. 2)

3.Turn the pressure washer upside down and slide the front support onto the unit. (Fig 2)

4.Using the 1” long nickel plated screw, secure the front support to

the unit. Wheel

Wheel

Lock

Wheel		Screw,
	Front	1” long,
Axle
		nickel plate
	Support
		Fig. 2

Attaching The Handle To The

Pressure Washer

1.	Place the handle on the unit as
	shown in Fig. 3.
2.	Push the handle in at the bottom
	until it is in position. (Fig. 4)
3.	Let the handle slide down to its
	resting place as shown in Fig 5 & 6.
4.	To secure the handle to the unit,
	screw 1 1/4” screw at the top hole
	and the two (2) 7/8” screws on each	Fig. 3
	side of the handle. (Fig. 7)		Fig. 4
			1 1/4”
		7/8”	SCREW	7/8”
		SCREW		SCREW

Attaching High Pressure Hose to Pressure Washer

Once the pressure washer is assembled, you are ready to use the unit.

1.While facing the rear of the unit attach the high pressure hose to the high pressure output connector on the back side of the unit. Twist on tight to avoid leakage. (Fig. 8)

Fig. 8

2.Then attach the other end of the high pressure hose to the high pressure hose connector on the trigger gun. (Fig. 9)

Fig. 9

3.Once the high pressure hose is connected to the trigger gun, you can attach the lance and accessories that you desire. To attach either the lance or the brush to the trigger gun, hold the trigger gun in your left hand insert the lance or the brush and push it in all the way into the connector on the trigger gun and turn it clockwise 60° until it locks in place. To remove the attachment, push down on the attachment and turn counter-clockwise 60° and then pull out. Make sure that the attachments are securely locked in place before use. (Fig. 10)

Garden Hose Connection

Once all the desired attachments and the high pressure hose are attached to the pressure washer, you can connect the garden hose to the unit.

1.Make sure that the water intake filter is inside the water intake inlet.

(Fig. 11)

2.Attach the male adapter (supplied) to the water intake connector on the front side of the unit. (Fig. 11)

3.Attach the female hose coupling to the garden hose. (Fig. 11)

4.Connect the female hose coupling to the male adapter making sure that it is tightly secured in place. (Fig. 11)

Water inlet

Water intake

filter

Garden hose (not supplied)

Fig. 11	Garden hose
Hose	coupling
connector

5. After all the connections have been

made and BEFORE you plug the

pressure washer into an electrical

outlet, open the water supply and

press on the trigger switch in order to

remove any air which may be in the

hose or pump. Continue to press on

the trigger switch until you get a

constant flow of water coming out of

the trigger gun. Allow water to flow

for 30 seconds.

6. Once this is accomplished, stop

pressing the trigger switch. Engage

the safety lock on the trigger.

7. Ensure that the "On/Off" switch, at

the side of the unit, is on the "Off"

position, then plug the unit into an

Fig. 5

Fig. 6

Fig. 7

Fig. 10

electrical outlet and turn the unit to

the "On" position.

8. Now you are ready to use the

pressure washer. Disengage the

safety lock and depress the trigger on

the trigger gun.

5

6