Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

• Change the hydraulic filter and fluid.

Every 500 hours

• Check the wheel hub slotted nut torque specifications.

• Check the wheel lug nuts.

 

 

• Check the park brake adjustment.

 

 

Every 4,000 hours

• Change engine coolant. Dex-Cool©extended life coolant (orange color)

 

 

Yearly

• Grease the deck and pump idler pivots.

• Grease the front caster pivots.

 

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick according to the engine manufacturer’s recommendations. Remove the dipstick and read the oil level.

4.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Use oil as specified in Engine Owner’s Manual. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge

Service Interval: As required

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter or with the message display. If the ignition key is turned to the “on” position for a few seconds, the battery voltage will be displayed in the area where the hours are normally displayed. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Voltage

Percent

Maximum

Charging

Reading

Charge

Charger

Interval

 

 

Settings

 

12.6 or

100%

16 volts/7

No

greater

 

amps

Charging

 

 

 

Required

12.4 – 12.6

75–100%

16 volts/7

30 Minutes

 

 

amps

 

12.2 – 12.4

50–75%

16 volts/7

1 Hour

 

 

amps

 

12.0–12.2

25–50%

14.4 volts/4

2 Hours

 

 

amps

 

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum

30

Page 30
Image 30
Exmark 4500-466 manual Check Engine Oil Level, Check Battery Charge

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.