
BB 710M • Installation Guide
Overview
|
|
|
|
|
|
|
| the |
|
|
|
|
|
|
| for | and | ||
|
|
|
|
| com |
|
| ||
|
|
|
|
| . |
|
|
|
|
|
|
| . | on. | manual | ||||
|
|
| on | ||||||
to |
| extr. | user | connecting | |||||
www |
|
|
| ||||||
Refer |
|
| before |
| . | ||||
|
| 710 |
|
| |||||
| to | series |
|
|
| ||||
|
|
|
|
|
| ce | |||
TLP |
|
|
| sour |
| ||||
| power |
|
| ||||||
complete | instructionsthe |
|
|
|
| ||||
installationprpr | toto |
|
|
|
|
|
| ||
the | oduct |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
The Extron BB 710M back box is used to mount an Extron TLP 710MV TouchLink™ panel in a wall. This Installation Guide provides instructions for an experienced installer to retrofit the box in existing drywall or mount the back box in a new installation. For complete instructions about installing and calibrating the TouchLink panel, see the TLP 710MV and TLP 710TV User Guide, which are available on the Extron web site (www.extron.com).
Retrofit an Existing Installation (with the Drywall in Place)
1. | Separate and remove the endplates (top and bottom) from the |
| ||
| back). |
|
|
|
2. | Use the back face of the | 7 | ||
| level to ensure the |
|
| |
| NOTE: | The hole is 7.7 inches (19.5 cm) wide x 6 inches (15.1 cm) high. |
| |
3. | Using a drywall saw, carefully cut a hole where the touchpanel will be installed. Cut on |
| ||
| the lines that you marked in step 2. |
| BB 710M | |
4. | Run the cable conduit through the wall. The conduit can be attached to any of the | |||
Tabs (4) | ||||
| available | Figure 1. | ||
| connect the conduit to the back box and the cables to the touchpanel. |
| ||
|
|
| ||
5. | Run cables to the installation site. |
|
| |
6. | Clear the cables and conduits from the space behind the hole. |
|
| |
7. | If required, secure a conduit to the |
| 9 | |
|
| |||
| into the hole (see figure 1). |
|
| |
| NOTE: | The |
| 10 |
|
|
|
| |
8. | Pull back the cables that were cleared out of the way in step 5. |
|
| |
9. | If required, secure one or more conduits to the |
|
| |
| the endplate (see figure 2). Break off the lip on the leading edge |
|
| |
| of the endplate (see figure 3) to make it easier to maneuver the | Figure 2. |
| |
| endplate with a conduit attached. |
|
10.Slide the endplates into the gap between the back of the U‑plate and the top flanges on the side of the U‑plate (see the inset in figure 2). The endplate must pass the drywall so that the trailing edge can be pushed in behind it.
11.Secure the endplate to the
The endplates (behind) and the tabs of the
Tabs are against outside surface of drywall.
12.Finish installing the TouchLink panel as shown in figure 4 and described in “Mounting the Touchpanel” on the next page.
Lip Snaps
Off
Slot
Threaded
Hole
Tighten screws to rotate locking arms.
Bezel snaps to unit
(4 places on each side).
Figure 3. | Figure 4. |
1