Extron electronic user manual BB 710M Installation Guide Cont’d, New Construction Installation

Models: BB 710M

1 2
Download 2 pages 29.13 Kb
Page 2
Image 2
BB 710M • Installation Guide (Cont’d)

BB 710M • Installation Guide (Cont’d)

New Construction Installation

1.Secure the endplates to the U-plate, using the four provided screws.

2.Before the drywall has been secured to the studs, place the wall box in a suitable place so that the tabs on the sides of the box are flat against a vertical stud.

3.Secure the wall box to the stud (metal or wooden) using two nails or screws.

4.Run the cable conduits to the box and connect them to one of the available knock-out holes. Leave enough cable to provide slack for installing the TouchLink panel.

5.Measure the position of the back box, and mark and cut a hole in the drywall where the box is placed.

New Construction Installation NOTE: The hole is 7.7 inches (19.5 cm) wide x 6 inches Mounting the Touchpanel (15.1 cm) high.

6.Secure the drywall to the studs.

 

Tabs are in contact

 

with the wall stud.

 

Extron BB 710M

 

Wall Box

 

for Wall-mounting

 

Extron TLP 710MV

3

Mounting Screws (2)

Figure 5.

Manual background NOTE: The tabs of the wall box sit on the stud against the inner face of the drywall.

7.If required, paint the drywall. Insert the cardboard cover (provided) into the back box to avoid getting paint on it.

Mounting the Touchpanel

For complete instructions about installing and calibrating the TouchLink panel, see the TLP 710MV and TLP 710TV User Guide, available on the Extron website

(www.extron.com).

1.Connect the cables to the back of the TouchLink panel (see the user guide). Feed excess cable back into the conduit.

2.Test the connections and configure the TouchLink panel (see the user guide).

3.Fold the locking arms into their recesses on the side of the touchpanel and slide the unit into the back box.

4.Tighten the screws on the front of the unit so that the locking arms rotate into place behind the top and bottom plates of the back box and hold the unit in place (see figures 4 or 6).

5.Snap the faceplate into position (see figures 4 or 6).

Tabs are against outside surface of wall stud.

Tighten screws to rotate locking arms.

Bezel snaps to unit

(4 places on each side).

Figure 6.

Extron Headquarters

 

Extron Europe

Extron Asia

Extron Japan

Extron China

Extron Middle East

Extron Korea

Extron India

+1.800.633.9876 (Inside USA/Canada Only)

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

+4000.398766

+971.4.2991800

+82.2.3444.1571

1800.3070.3777

Extron USA - West

Extron USA - East

(Inside Europe Only)

(Inside Asia Only)

+81.3.3511.7656 FAX

Inside China Only

+971.4.2991880 FAX

+82.2.3444.1575 FAX

Inside India Only

+1.714.491.1500

+1.919.850.1000

+31.33.453.4040

+65.6383.4400

 

+86.21.3760.1568

 

 

+91.80.3055.3777

+1.714.491.1517 FAX

+1.919.850.1001 FAX

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

+86.21.3760.1566 FAX

 

 

+91.80.3055.3737 FAX

 

 

 

 

 

 

 

 

 

© 2012 Extron Electronics All rights reserved. www.extron.com

68-2150-01 Rev. B

2

07 12

 

Page 2
Image 2
Extron electronic user manual BB 710M Installation Guide Cont’d, New Construction Installation, Mounting the Touchpanel