Front Panel Features
1
CONFIG
2 | 3 | 4 | 5 |
| MENU |
| ADJUST |
| NEXT |
|
|
Extron
DVC 501 SD
DIGITAL VIDEO CONVERTER
A USB Config port | B LCD screen | C Menu button | D Next button | E Adjust knobs |
Configuring the DVC 501 SD Using the Front Panel
Menu selections are displayed on the LCD screen. To use any menu, press the Menu button repeatedly until the desired menu is displayed (see the menu flow diagram below). Press the Next button repeatedly until the desired submenu appears. Rotate an Adjust knob to select an item from a submenu. To return to the main menu at any time, press the Menu button. After 30 seconds of inactivity, the screen displays the default cycle.
1. From the Output Config submenus, use the Adjust knobs to select the output signal |
| Default |
| ||||||||
type and the sync polarity to match the requirements of the display device. |
|
|
| ||||||||
|
| Cycle |
| ||||||||
2. From the Advanced Config menu, Test Pattern submenu, select the Crop, Crosshatch, |
|
|
| ||||||||
Colorbars, and Grayscale test patterns to confirm that the settings of the display device |
| Menu |
| ||||||||
are correct. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
NOTE: | Test pattern timings are based on the incoming SDI signals and are not |
| OUTPUT |
| |||||||
| CONFIG | 30 sec. | |||||||||
| displayed if an active signal is not present. |
|
|
|
| ||||||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| Menu |
|
3. Use the Audio Config submenus to configure the audio as desired. |
|
|
| AUDIO |
| ||||||
|
|
|
|
|
|
|
|
|
|
| |
Supported Input Resolutions |
|
|
|
|
|
| CONFIG | 30 sec. | |||
|
|
|
|
|
| Menu |
| ||||
|
|
|
|
|
|
|
|
|
|
| |
Supported |
|
|
|
|
|
|
|
| Menu | ADVANCED |
|
Resolutions | 23.98 Hz | 24 Hz | 25 Hz | 29.97 Hz | 30 Hz | 50 Hz | 59.94 Hz | 60 Hz |
|
| |
| CONFIG | 30 sec. | |||||||||
|
|
|
|
|
|
|
|
|
| ||
720p |
|
| X | X | X | X | X | X |
| Menu |
|
|
|
|
|
|
|
|
|
|
|
| |
1080i |
|
|
|
|
| X | X | X |
|
|
|
1080p | X | X | X | X | X | X | X | X |
| EXIT MENU |
|
| PRESS NEXT | 30 sec. | |||||||||
|
|
|
|
|
|
|
|
|
| ||
NTSC |
|
|
|
|
|
| X |
|
| Next |
|
|
|
|
|
|
|
|
|
|
|
| |
PAL |
|
|
|
|
| X |
|
|
|
|
|
NOTE: The output resolution always matches the input resolution.
Simple Instruction Set (SIS) Commands
When setting up the DVC 501 SD, you can issue SIS commands from your computer via
Command | ASCII command | Response | Additional Description | |
(Host to Converter) | (Converter to Host) | |||
|
| |||
|
|
|
| |
|
|
|
| |
Mute video | 1B | Vmt1] | Mute the video output. | |
Unmute video | 0B | Vmt0 ] | Display the video output. | |
|
|
|
| |
Mute audio | 1Z | Amt1 ] | Mute the audio output. | |
Unmute audio | 0Z | Amt0 ] | Unmute the audio output. | |
|
|
|
| |
Enable lock (executive) mode | 1X | Exe1] | Lock all front panel functions. | |
Disable lock mode | 0X | Exe0 ] | Enable all front panel functions. | |
|
|
|
|
2 | © 2011 Extron Electronics All rights reserved. www.extron.com |
|
09 11
