DVI DL 101 Setup Guide
| |
| DVI DL 101 |
POWER | DVI DL 101 |
12V | |
0.2A MAX |
|
The Extron® DVI DL 101 is a dual link cable equalizer that extends DVI signals beyond the specified cable limits of
15 feet (5 m). It attaches to the end of a long cable run of up to 275 feet (84 m) for dual link and up to 200 feet (61 m) for single link. The DVI DL supports all dual link DVI signals up to 330 MHz, including 2560x1600 or1080p at 60 Hz. It is backwards compatible with single link, therefore supporting all single link rates up to 165 MHz, including 1920x1200 and 1080p at 60 Hz.
This guide provides basic instructions for an experienced installer to set up and operate this cable equalizer.
Installation Procedure
1.Turn off and disconnect all equipment from the power source.
2.(Optional) If desired, mount the DVI DL on a 9.5, 6, or 3.5 inch deep rack shelf; a projector mounting pole; or furniture.
3.Connect a DVI source device to the
4.Connect a DVI output device to the
NOTE: Dual link DVI cables must be used for
dual link DVI signals. If a single link
DVI cable is used, only single link DVI signals are possible.
5.Wire the provided power supply as illustrated below and connect it to the
SmoothRidges
A | A |
Tie
Power SupplyWrap
Output Cord
3/16” (5 mm)
MAX
SECTION | Captive Screw Connector |
Figure 1. Wiring the Power Connector
|
|
|
| 1 |
| 8 |
|
|
| |||||||||
|
| 9 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 17 | 24 |
|
|
| |||||||||||
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pin | Signal |
| Pin |
|
|
| Signal | Pin | Signal | |||||||||
1 | TMDS data 2– |
| 9 | TMDS data 1– | 17 | TMDS data 0– | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
2 | TMDS data 2+ |
| 10 | TMDS data 1+ | 18 | TMDS data 0+ | ||||||||||||
|
|
|
|
|
|
| ||||||||||||
3 | TMDS data |
| 11 | TMDS data 1 | 19 | TMDS data 0/5 | ||||||||||||
| 2/4 shield |
|
| shield |
| shield | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
4 | TMDS data 4– |
| 12 | TMDS data 3– | 20 | TMDS data 5– | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
5 | TMDS data 4+ |
| 13 | TMDS data 3+ | 21 | TMDS data 5+ | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
6 | DDC clock |
| 14 | +5 V power | 22 | TMDS clock | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| shield |
7 | DDC data |
| 15 | Ground (+5 V) | 23 | TMDS clock+ | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
8 | CEC control* |
| 16 | Hot plug | 24 | TMDS clock– | ||||||||||||
|
|
|
| detector |
|
| ||||||||||||
*CEC control on pin 8 is a proprietary usage, and is not the industry standard.
Table 1. DVI Connector Pin Assignments
CAUTION: The power supply must not be permanently fixed to the building structure or similar structures. The power supply must not be located within environmental air handling spaces or the wall cavity.
The installation must be in accordance with the applicable provisions of the National Electrical Code ANSI/NFPA 70, Article 725 and the Canadian Electrical Code, Part 1, Section 16.
The power supply must be located within the same vicinity as the Extron A/V processing equipment in an ordinary location, Pollution Degree 2, secured to a podium, a desk, or an equipment rack within a dedicated closet.
CAUTION: Applying power with incorrect voltage polarity can damage the power supply and equalizer. Identify the negative lead by the ridges on the side of the cord. (See the illustration above.)
CAUTION: Always use a power supply by Extron for the DVI DL 101. Use of an unauthorized power supply voids all
regulatory compliance certification and may cause damage to the supply and the DVI DL.
SW4 3G | 1 |
