Extron electronic SDI-AVR 100 manual Installation, Front Panel Indicators, Rear Panel Controls

Installation

	IN	SOG RGB/YUV UPSET	BETA COLORBARS	NTSC/PAL		R/R-Y	G/Y	B/B-Y	5
	OUT				COMPOSITE	H	V	S
						S-VIDEO
					OUTPUT	OUTPUT
	ON
	OFF
100-240V	50/60 Hz 0.2A

SDI INPUT OUTPUTS

6 1 2 7 3 4

Figure 4 — SDI-AVR 100 rear panel

SOG	RGB/YUV	SET UP	BETA	COLOR BARS NTSC/PAL
ON
OFF
SOG OFF/ON	RGB/COMPONENT	BI/TRI-LEVEL	SPARE

ON

OFF

RGB/Component (HDSDI-ACR 100) or RGB/YUV (SDI- AVR 100) switch — Set this switch to the Off position to output RGB video. Set the switch on for component video.

Bi/tri-level switch (HDSDI-ACR 100 only) — Set this switch to the On position to output tri-level sync on the component video output. Set the switch off for bi-level sync.

3Composite Output connector (SDI-AVR 100 only) — Connect a composite video display device to this BNC connector. This output is available whenever an active SDI signal is applied to the SDI input connector, 1 .

4S-video Output connector (SDI-AVR 100 only) — Connect an S-video device to this 4-pin mini DIN connector. This output is available whenever an active SDI signal is applied to the SDI input connector, 1 .

5RGB/component video output connectors

Ensure that the rear panel DIP switches are in the correct configuration (see Rear Panel Controls).

HDSDI-ACR 100 switch configuration

		RGB/
Output video format	SOG	Component	Bi/tri-level
RGBHV/RGBS	Off	Off	Either
RGsB	On	Off	Either
Y, R-Y, B-Y w/ bi-level on Y	Either	On	Off
Y, R-Y, B-Y w/ tri-level on Y	Either	On	On

SDI-AVR 100 switch configuration

Output video format	SOG	RGB/YUV
RGBHV/RGBS	Off	Off
RGsB	On	Off
Y, R-Y, B-Y	Either	On

RGBHV

Video

RGBS

Video

RGsB or Component Video

R/R-Y G/YB/B-Y

HVS

R/R-Y G/YB/B-Y

HVS

R/R-Y G/YB/B-Y

HVS

RGBHV video connection — Connect to five BNC connectors as shown.

RGBS video connection — Connect to four BNC connectors as shown.

RGsB and component video connection — Connect to three BNC connectors as shown.

6AC power connector — Plug a standard IEC power cord into this connector to connect the converter to a 100 to 240VAC, 50 Hz or 60 Hz power source.

Set Up switch (SDI-AVR 100 only) — Set this switch to the On position to output an NTSC signal that is on the 7.5 IRE pedestal. Set the switch off to return the signal to the normal level.

Beta switch (SDI-AVR 100 only) — Set this switch to the On position to set the color level of the YUV output to the Betacam level. Set the switch off to restore the YUV output to the normal level. If a Betacam signal is input, the switch should be set to On to output the Betacam format. Otherwise, the output will be NTSC or PAL.

Color Bars switch (SDI-AVR 100 only) — Set this switch to the On position to output NTSC or PAL color bars. Set the switch off for the converted video input.

NTSC/PAL switch (SDI-AVR 100 only) — Used in conjunction with the Color Bars switch only, set this switch to the On position to output PAL color bars. Set the switch off for NTSC color bars.

Rear Panel Controls

7DIP switches

SOG switch — Set this switch to the On position to output sync- on-green for RGB video (RGsB). Set the switch off for RGBHV or RGBS video.

Front Panel Indicators

All indicators are on the front panel. Figure 5 and figure 6 show HDSDI-ACR 100 and SDI-AVR 100 indicators.

1Power LED — The Power LED indicates that power is on.

2720P LED (HDSDI-ACR 100 only) — The 720P LED indicates that the converter is outputting the HDTV 720P video format.

4 HDSDI-ACR 100 and SDI-AVR 100 • Installation HDSDI-ACR 100 and SDI-AVR 100 • Installation and Operation 5