Extron electronic HSA 800, HSA 802 Adding a Second Connector Panel

Surface Access Products • Maintenance and Modifications

Surface Access Products • Maintenance and Modifications

Maintenance and Modifications, cont’d

Mounting

Surface

Clamshell

Full Thread

Mounting Bolts

AAP Cables

Flat Washer

IEC Power Cord

RJ-45 Connectors

Shroud

HSA 802

Remove 16

screws

125 - 50/60 Hz 0.5A

COMPUTER

INPUT

SELECT

AUDIO

Figure 3-3 — Removing the HSA 802 from the table

17. Carefully lower the HSA enclosure into the table opening.

From the underside, bolt the clamshell to the enclosure

with the two bolts removed in step 5.

3-73-6

Figure 3-4 — Disconnecting the interior AC cable

18. Connect the IEC power cord and RJ-45 cables to the

connectors on the underside of the surface mount

enclosure.

19. To prevent wear and tear caused by cable movement,

secure the AAP cables underneath the table. See Routing

the AAP Cables in chapter 2, Installation.

Adding a Second Connector Panel

The standard HSA 800 includes one connector panel with the

associated connectors and AAP opening. Non-US/domestic

versions also have a separate AC connector panel. Future needs

may demand adding a second connector panel and, for non-

US/domestic versions, an AC panel (in effect converting the

HSA 800 into an HSA 802). Add the additional panels as

follows:

Ensure that AC power is disconnected before

servicing the HSA unit.

Contents

Main Users Manual HSA 800 & 802 Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan Precautions Instrucciones de seguridad Espaol Caution Warning Attention Table of Contents Page Surface Access Products Introduction 1-3 Introduction xi About the HSA Hideaway Enclosures Figure 1-1 HSA 800 hideaway enclosure 1-2 Chapter Two Installation Features Installation 2-3 Figure 2-1 Prepared mounting template 2-2 Preparing the Table and Mounting the Enclosure 2-52-4 Figure 2-2 Cutting the opening with a router 2-6 Figure 2-3 Mounting the HSA 800 enclosure 2-7 Cabling and Installing the AAPs Figure 2-4 Removing the front panel from an HSA 800 2-8 RGB 580xi SI AAP 2-9 Cabling the enclosure Figure 2-6 HSA 800 and HSA 802 enclosure underside connectors Figure 2-7 HSA 802, US/domestic RJ-45 connectors Figure 2-8 HSA 802, IEC/international RJ-45 connectors Figure 2-9 Changing the connector icon Bezels Surface Access Products Chapter Three Maintenance and Modifications Maintenance and Modifications 3-2 Replacing an AAP 3-3 RGB 580xi SI AAP Removing and Replacing the Enclosure 3-53-4 Figure 3-3 Removing the HSA 802 from the table 3-73-6 Figure 3-4 Disconnecting the interior AC cable Adding a Second Connector Panel Replacing the Gas Lift 4,7 3-93-8 5,6 2,9 Figure 3-5 Changing the gas lift Adjusting the Top Surface Adjusting the height of the top surface 3-11 Figure 3-5 Location of the height adjustment screw Adjusting the top surface level A Appendix A Reference Information Reference Information A-3A-2 Specifications General A BC Reference Information, contd A-4 HSA 800/802 EU Part number A-5 HSA 800/802 UK Part number Reference Information, contd Top Plate Dimensions CUT-OUT TEMPLATE FOR EXTRON'S HSA 800 & 802 SURFACE CUT-OUT AREA = C x D Page Figure B-1 HSA 800/802 return kit B-3B-2 Figure B-2 Attaching the clamshell Figure B-3 Installing protective strips Packaging for Shipment Packaging for Shipment, Contd B-5B-4