Y/VID
Tighten the screws to secure the board.

PowerCageMTP T AV and MTP R AV Board

Setup Guide

 

PowerCage

 

MTP R AV

 

INPUT

C

 

Y/VID

 

MONO AUDIO OUTPUT

1 2

 

GAIN

 

SHARP

MTP R AV

 

PowerCage

 

MTP T AV

 

OUTPUT

C

 

Y/VID

 

INPUT

R

AUDIO

L

MTP T AV

The Extron® PowerCage MTP T AV and MTP R AV are twisted pair transmitters and receivers in a modular board format for the PowerCage 1600 modular enclosure. They transmit or receive composite video or

S-video and audio over CAT 5-type cable.

Both boards can be used with any CAT 5, 5e, or 6 cable, or Extron Enhanced Skew-FreeA/V UTP cable for cable runs up to 1000 feet

(300 m). The boards mount in any of the 16 expansion slots at the rear of the PowerCage 1600.

Refer to the PowerCage MTP T AV and MTP R AV User Guide and the PowerCage 1600 Enclosure User Guide, available at www.extron.com.

NOTE: The hot-swappable, modular design allows for replacing or upgrading boards in the field at any time, without having to power down the system.

Installation

1.Select an open slot at the rear, or take out a blank plate by loosening the two screws (top and bottom), and lifting the blank away.

NOTE: If a board is already in the slot, loosen the screws and remove the board.

2.Remove the new board from the box, holding the board by the frame.

3.Hold the board with the signal connectors

towards you and the MTP AV board name and LED at the top, and align the top and bottom grooves of the board with the slide posts in the selected enclosure slot.

4.Carefully slide the board into the slot, aligning that the two tabs on the lower front end of the board with the matching

ports in the enclosure. Push the board firmly into place.

5.

6.If applicable, repeat steps 1 through 5 for any other modular boards.

16 Available Single Board Slots or

 

 

8 Double Board Slots

 

 

Power

 

 

 

 

INPUT

 

 

Supply

 

 

 

Tx Rx

 

 

 

 

 

 

 

C

 

 

 

 

Rx

 

 

2

Align board and

 

 

Tx

REMOTE

1 2

 

 

FIBER

 

TxRx

 

 

 

 

 

TxRx

232RS-

A

slide into slot.

RS-232

OVER

R

 

 

AUDIO L

 

T

 

 

OUTPUT

 

RGB

 

 

 

 

 

 

 

 

 

Tx Rx

1 2

 

 

232-RS

TxRx

FIBER

TxRx

REMOTE

232RS-

R

 

OVER

AUDIO L

 

Screws

 

OUTPUT

RGB

(2 per board)

 

 

 

NOTE: Cover all empty board slots; do not leave them open. Using a tool, securely fasten the screws for boards and blank panels after initial installation and subsequent removal and replacement of the boards.

7.If power has been removed, reconnect and power on the PowerCage. The LED on

the board lights green and the new board is auto-detected.

Y/VID

C

8.Following the image at right, connect input or output device cables to the the two BNC connectors for S-video signals or for composite video signals.

S-video

OR

C

Composite

Video

Continued on side 2.

1

 

Page 1
Image 1
Extron electronic setup guide PowerCage MTP T AV and MTP R AV Board Setup Guide, Installation

MTP R AV, MTP T AV specifications

Extron Electronics has long been a prominent player in the AV distribution market, and their MTP T AV and MTP R AV series reflect their commitment to quality, innovation, and versatility. These devices are essential in extending audio and video signals over twisted pair cabling while maintaining exceptional performance.

The MTP T AV, or the Master Transmitter, is designed to send high-quality AV signals such as composite video, S-video, and stereo audio over long distances using a single Category 5e or 6 cable. One of its key features is the support for resolutions up to 1080i, ensuring compatibility with a wide range of display technologies. It incorporates Extron's advanced transmission technology which minimizes noise interference, delivering a clean and reliable signal.

On the other hand, the MTP R AV acts as the Receiver, reconstituting the transmitted signals and making them ready for display. It features automatic input detection, simplifying the setup process and ensuring optimal performance based on the incoming signal. Like its counterpart, the MTP R AV also supports high-quality audio and video formats, making it a versatile choice for various setups.

Both the MTP T AV and MTP R AV utilize Extron’s patented Technology, which includes a built-in adaptive equalizer that automatically compensates for cable length. This ensures that even at the maximum distance, the signal quality remains intact. The devices also feature a robust locking mechanism for a secure connection, which is crucial in professional environments where reliability is paramount.

Another notable characteristic of these devices is their compact design, which allows for easy integration in racks or wall plates without occupying significant space. Their user-friendly interface and intuitive controls make installation and operation straightforward for AV professionals.

The MTP series is further enhanced by the ability to work with Extron’s extensive line of control systems, ensuring seamless integration into modern AV environments. Whether used for classrooms, conference rooms, or large-scale events, the MTP T AV and MTP R AV offer scalable solutions that cater to diverse AV distribution needs.

In summary, Extron's MTP T AV and MTP R AV represent the pinnacle of AV signal distribution technology. With their high-resolution support, adaptive equalization, and user-friendly design, these devices are ideal for a wide range of applications in the ever-evolving world of audiovisual technology.