Installation and Operation
Description
The P/2 DA2 MT Distribution Amplifier can be mounted using the included mounting brackets and screws. Audio input and output connectors and an external DC power supply are also features of the P/2 DA2 MT. See example application diagram below.
Stereo
Output
P/2 DA2 MT
Easy Setup Procedure
These
1. If the P/2 DA2 MT is to be mounted using the mounting | |
| brackets, please refer to the previous section. |
2. | Power off the computer and its local monitor. |
3. | Connect the computer’s VGA output to the |
| input on the front panel of the P/2 DA2 MT. |
4. | If a local monitor is being used, connect the monitor to the 15- |
| pin local monitor output on the front panel. |
5. | Set termination pins (see Front Panel DIP Switch Settings |
PC Audio |
Input |
| P/2 | DA2 |
|
|
|
|
| MT |
|
| |
|
|
| With |
| |
|
|
|
|
| |
|
|
|
| Mounting |
|
|
|
|
| Brackets |
|
|
|
|
| or |
|
PC Computer |
|
|
| Projector | Video Monitor |
Front Panel
Mounted under a Desk
or
Mounted in a Table
D2/P
TM2A
below). |
6. If audio is being input, connect the audio source to the 3.5 mm |
audio input jack on the front panel. Refer to the audio |
connector diagrams on the last page. |
7. Connect the output display device, such as a projector, VGA- |
compatible monitor, etc., to the |
connector on the rear panel of the P/2 DA2 MT. |
8. Connect an audio device to the 3.5 mm captive screw audio |
The front panel consists of a
COMPUTER | BUFFERED I D P I N 4 | I D P I N 1 1 |
I N P U T | L O C A L M O N I TO R | P/2 DA2 MT |
Rear Panel
The rear panel consists of a
POWER | S PA R E | L E V E L / P E A K I N G | DATA DISPLAY | |||
9V DC |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.5A MAX.
Mounting Bracket
The included mounting brackets are attached to the P/2 DA2 MT using the 6 bracket screws, as shown on page 5. The unit may then be mounted under a desk or some other suitable location using the 4 wood screws (see mounting template). Optional brackets are also available for vertical mounting (see mounting template).
output connector on the rear panel. Refer to the audio |
connector diagram on the following page. |
9. Connect the |
into the power input jack on the rear panel. | I D P I N 4 I D P I N 1 1 |
Front Panel DIP Switch Settings
Set the two DIP switch pin positions (on/up or off/down):
Pin 4 | Pin 11 | Function |
off | off | computer input pins 4 & 11 passed to |
|
| local monitor output connector |
on | on | provide ID bit termination when no |
|
| local monitor connected |
on | off | provide correct MAC 13” ID bit |
|
| termination |
Rear Panel DIP Switch Settings
Set the Level/Peaking DIP switch On (up) to increase level and peaking of the data display, otherwise, set the switch Off (down).
Operation
1.Power on the computer and monitor.
2.Power on the output display device.
3.Power on the P/2 DA2 MT. The LED will light amber when the power is on and will light green when the power is on and there is an input present.
2 | P/2 DA2 MT • Installation and Operation | P/2 DA2 MT • Installation and Operation | 3 |