Introduction
The P/2 DA2xi and the P/2 DA2xi MT are distribution amplifiers that accept video input from a VGA, XGA, or UXGA compatible PC and distribute the signal to separately buffered outputs. Each output can be extended with Extron
Both models can be powered by newer computers compatible with the new VESA standard using pin 9 of the VGA connector as the +5VDC source. An external power supply is also provided for use with older computers, where power is unavailable through the VGA connector, or the available power is inadequate.
Features
•Powered by computer — This unit can be powered by most newer computers.
•Power/Signal LED — Green LED = power + signal. Amber LED = Power but no signal. Off = no power.
•Gain/Peak DIP switch — To compensate for longer cable runs. Switch to on (up) when output cable is over 100’ (30.5 m).
•Out Imp DIP switch — Changes the output impedance to be compatible with all projectors.
Installation
The P/2 DA2xi and P/2 DA2xi MT can be mounted on a rack shelf, under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the P/2 DA2xi or P/2 DA2xi on a VersaTools 19" 1U Rack Shelf (part
Only products in the VersaTools line can be mounted to a
VersaTools rack shelf.
INPUT |
IN | MONITOR |
PUT |
M | NIO ORT |
|
I |
NPUT |
MONI TOR |
M | DA |
|
|
|
ISTRD | SER |
| ||
| IBU |
| ||
|
| TIONAM | IES | |
|
|
| PLIF | RIE |
Figure 2 — Mounting the P/2 DA2xi and P/2 DA2xi MT on the standard rack shelf
1. | Remove the rubber feet (if installed) and mount the unit on the |
| rack shelf, using two screws in opposite (diagonal) corners. |
2. | Install blank panel(s) or other unit(s) to the rack shelf. |
3.Insert the shelf into the rack, and secure the shelf to the rack using the supplied machine screws.
Furniture or projector mounting
Furniture mount or projector mount the unit using the optional mounting kit (part
1. Attach the mounting brackets to the P/2 DA2xi or
P/2 DA2xi MT with the provided machine screws (figure 3).
Projector
Mounting
Bracket
Mounting
Bolt
PIN TU |
|
|
|
|
|
|
|
|
|
|
|
MO | ITN |
|
|
|
|
|
|
|
|
|
|
| OR |
|
|
|
|
|
|
|
|
| |
|
| IN | PU |
|
|
|
|
|
|
|
|
VersaTools Rack Shelf |
|
|
|
|
| M | NITO | O | R |
|
|
1/4 Rack Width False |
|
|
|
|
|
|
|
|
| ||
Front Face Plate |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| IN | UP |
|
|
|
|
|
|
Use 2 mounting holes |
|
| T |
|
|
|
|
| |||
|
|
|
|
|
| M | ON | ITOR | |||
on opposite corners. |
|
|
|
|
|
|
|
|
|
(2)
INP | U T |
M | ONIT |
|
|
| O R |
Ceiling
Digital Projector
Figure 1 — Rack mounting the P/2 DA2xi and P/2 DA2xi MT on the VersaTools rack shelf
2P/2 DA2xi and P/2 DA2xi MT • Installation
Figure 3 — Desk and projector mounting the P/2 DA2xi or P/2 DA2xi MT
P/2 DA2xi and P/2 DA2xi MT • Installation | 3 |