SIS™ Commands
PVS 204SA Plus specific symbol definitions
Symbols (X/ values) defined here are used throughout the command/response table below.
The symbols represent variables in the
] = CR/LF (carriage return/line feed) (hex 0D 0A)
}= CR (no line feed)
• = Space E = Escape key
X! = Input numbers 1 through 4, and 7;
0 = all outputs muted (both audio and video)
1 and 2 = RGB inputs (also 1 and 2 in RGB/VGA group)
3 and 4 = Composite video inputs in Single Switch Mode. In Separate Switch Mode, composite video inputs are identified as 1 and 2 in the Composite Video/Vid Group
7 = Aux/Mix input (not applicable with audio and video breakaway commands)
X# = Status 0 = Off 1 = On
X2# = Video type (inputs 3 and 4 only) 1 = Composite video (default)
2 = RGB
X2$ | = Video signal status | |
| 1 | = A video signal present |
| 2 | = No video signal detected |
X2% | = 0 to 15 microphone | |
| default = 8 | |
X2^ | = 0 to 30, program audio ducking level in | |
| default = 6 | |
X2& | = Lineout status | |
| 1 | = variable (default) |
| 2 | = fixed |
X2* | = VCM mute mode status | |
| 1 | = mute all (Aux/Mix and program) audio (default) |
| 2 | = mute Aux/Mix audio (program goes through) |
| 3 | = mute program audio (Aux/Mix goes through) |
X2( | = Paging delay on 1 second steps; default = 0 (disabled), | |
| 1 | = 1.0 second, 2.0 = 2 second, ..., 8 = 8.0 second |
SIS Command/Response Table
Command | ASCII (Telnet) | Response |
| (host - switcher) | (switcher to host) |
Video Configuration |
|
|
Set the video signal type | X!*X2#\ | TypX!= X2#] |
View the video signal type | X!\ | TypX!= X2#] |
Status Commands |
|
|
View all input status | LS | Frq= X2$*X2$*X2$*X2$] |
View paging sensor status | 42S | Sts42*X#] |
Mic |
|
|
Adjust
Program Audio Ducking Level
2*X2%# | ThrX2%] |
ThrX2%] | |
+*2# | ThrX2%] |
2# | ThrX2%] |
Adjust audio ducking level | 58*X2^# | AdlX2^] |
Increment audio ducking | +*58# | AdlX2^] |
Decrement audio ducking | AdlX2^] | |
View audio ducking | 58# | AdlX2^] |
Set Lineout Mode |
|
|
Set lineout to variable | 55*1# | LineOut*X2&] |
Set lineout to fixed | 55*2# | LineOut*X2&] |
View lineout mode | 55# | LineOut*X2&] |
VCM Mute Mode |
|
|
Mute all (Aux/Mix and program) audio | 74*1# | VCMX2*] |
Mute Aux/Mix audio (program goes through) | 74*2# | VCMX2*] |
Mute program audio (Aux/Mix goes through) | 74*3# | VCMX2*] |
VCM mute mode status | 74# | VCMX2*] |
Paging Sensor Delay |
|
|
Set paging sensor delay | 75*X2(# | PageDly*X2(] |
View paging sensor delay | 75# | PageDly*X2(] |
For all PoleVault device specifications, optional accessories, and part numbers, visit www.extron.com
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500 +1.714.491.1517 FAX
4
Extron USA - East | Extron Europe | Extron Asia | Extron Japan |
+800.633.9876 | +800.3987.6673 | +800.7339.8766 | +81.3.3511.7655 |
Inside USA / Canada Only | Inside Europe Only | Inside Asia Only | +81.3.3511.7656 FAX |
+1.919.863.1794 | +31.33.453.4040 | +65.6383.4400 |
|
+1.919.863.1797 FAX | +31.33.453.4050 FAX | +65.6383.4664 FAX |
|
© 2009 Extron Electronics. All rights reserved.
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568 +86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800 +971.4.2991880 FAX
Rev. B
04 09
