TOOLS NEEDED FOR INSTALLATION

Saber Saw or Jig Saw

Drill

1 1/4" Wood Drill Bit

Pliers

Phillips Screwdriver

Flat Blade Screwdriver

Wire Stripper or Utility Knife

Metal Snips

Measuring Tape or Ruler

Level

Pencil

Caulking Gun

Duct Tape

PARTS SUPPLIED FOR INSTALLATION

1 Hardware Package

1 Literature Package

PARTS NEEDED FOR INSTALLATION

2 Conduit Connectors

Power Supply Cable

1 Wall or Roof Cap

All Metal Ductwork

OPTIONAL ACCESSORIES AVAILABLE

High Ceiling Chimney Kit

Extends the island chimney for high ceilings

part # 620000558 - Stainless

*Ductless Conversion Kit

For non-vented installations only

* it is highly recommended that professional style cooking always be vented to the outside

part # 620000557 - Stainless

Replacement Charcoal Filter

For non-vented installations only, replace charcoal filter as needed part # 620000041

RANGEHOOD COMPONENTS

A. CANOPY SECTION

B. LOWER CHIMNEY COVER

C. UPPER CHIMNEY COVER

D. CHIMNEY SUPPORT

E. CANOPY SCREWS

F. WOOD SHELF BOLTS

G. PLUGS - DO NOT USE

H. WOOD SHELF WASHERS

I. WOOD SHELF NUTS

J. MOUNTING TEMPLATE

K. CONNECTOR BOX HALVES

L. CONNECTOR BOX SCREWS

M. CONNECTOR BOX SCREWS

N. DAMPER

O. EASY CUBE™

FIGURE 1

UNPACK THE RANGEHOOD

Remove the rangehood from the carton and place on a flat surface for assembly. Before discarding the packaging, check to make sure that no mounting hardware or parts are missing. DO NOT REMOVE THE PLASTIC COVERING ON THE CHIMNEYS AT THIS TIME! This plastic covering protects the chimney from scratches during installation.

For safe packaging, the entire chimney section of the hood is shipped assembled. It must be disassembled completely for installation. Disassemble packaged chimney components by sliding apart the chimney covers (B and C in FIGURE 1). Remove the LOWER CHIMNEY COVER (B) from the CHIMNEY SUPPORT (D) by removing the 2 philips screws on the outside bottom of the chimney cover. Remove the UPPER CHIMNEY COVER (C) from the CHIMNEY SUPPORT (D) by removing the 2 philips screws on the outside top of the chimney cover.

PREPARING TO ATTACH THE CHIMNEY

The rangehood attaches to the ceiling by a metal support structure (D in FIGURE 1). This support must be attached to the ceiling before the canopy is attached. This structure must be firmly attached to the ceiling.

FOR WOOD CEILINGS: Use four 4" long wood screws and washers.

FORPLASTERORSHEETROCKCEILINGS: If possible, the support must be attached to the ceiling joists. If not, a supporting structure behind the sheet rock must be built.

FOR WOOD SHELVES: Use items F, H, & I in FIGURE 1.

CALCULATE THE DUCTRUN LENGTH

The ductrun should not exceed 35 equivalent feet if ducted with the required minimum of 6" round duct. Calculate the length of the ductwork by adding the equivalent feet in FIGURE 2 for each piece of duct in the system. An example is given in FIGURE 3.

For best results, use no more than three 90° elbows. Make sure that there is a minimum of 24" of straight duct between elbows if more than one is used. Do not install two elbows together. If you must elbow right away, do it as far away from the hood's exhaust opening as possible.

45˚ Elbow

3.0 feet

90˚ Elbow

5.0 feet

90˚ Flat Elbow

12.0 feet

Wall Cap FIGURE 2

0.0 feet

 

 

 

9

Feet Straight Duct

9.0 feet

2

- 90˚ Elbows

10.0 feet

Wall Cap

0.0 feet

 

Total System

19.0 feet

 

FIGURE 3

 

 

 

 

 

 

Version 08/06 - Page 4

Page 4
Image 4
Faber Diamante Isola manual Tools Needed for Installation, Parts Supplied for Installation, Parts Needed for Installation