PLAN THE INSTALLATION
This rangehood can be installed as either ducted or ductless. When installed ductless, the rangehood vents out of a grate on the back of the lower chimney. Ductless installations require a Ductless Conversion Kit, available from your dealer.
WARNING! BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, DETERMINE WHICH VENTING METHOD WILL BE USED AND CAREFULLY CALCULATE ALL MEASUREMENTS.
| DUCTED INSTALLATION DIMENSIONS |
(vented to the outside) |
The Diamante Isola chimney is highly adjustable and designed to meet varying ceiling heights as indicated in FIGURE 4. The chimney can be adjusted for ceilings between 7' 5 9/16" and 9' 3/16" depending on the distance between the bottom of the hood and the cooktop (distance x in FIGURE 4).
For higher ceiling installations, the High Ceiling Chimney Kit includes an additional support structure which adds 27 1/2" to the ceiling heights in FIGURE 4.
| upper |
| 2 3/4” |
| min |
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||||||
| chimney |
|
|
|
|
|
|
| |||||
|
| 15 3/8” | max |
|
|
|
|
| |||||
| cover |
|
| FIGURE 4 | |||||||||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| DUCTED | |||
|
|
|
|
|
|
|
|
|
| ||||
| lower |
|
|
|
|
|
|
| DIMENSIONS | ||||
| chimney |
| 23 5/8” |
|
|
|
|
|
|
|
| ||
| cover |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| canopy |
|
| 3 3/16” |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||||
x=distancefromhoodtocooktop |
|
|
|
|
| min & max ceiling height examples |
| ||||||
|
|
| |||||||||||
|
|
|
| x = 24" | x = 26" | x = 28" | x = 30" | ||||||
(varies depending on installation) |
| x |
|
| min | min | min | min | |||||
min - 24”, suggested max - 30” |
|
|
| ||||||||||
also consult cooktop |
|
|
|
| 7' 5 9/16" | 7' 7 9/16" | 7' 9 9/16" | 7' 11 9/16" | |||||
manufacturer's recommendation |
|
|
|
|
| max | max | max | max | ||||
|
|
|
|
|
|
| 8' 6 3/16" | 8' 8 3/16" | 8' 10 3/16" | 9' 3/16" |
| ||
|
|
|
|
|
| ||||||||
cabinet base | 36” |
|
|
WARNING !
DUE TO THE SIZE AND WEIGHT OF THIS R A N G E H O O D , T H E SUPPORT MUST BE FIRMLY ATTACHED TO THE CEILING. For plaster or sheet rock ceilings, the support must be attached to the joists. If this is not possible, a support structure must be built behind the plaster or sheet rock. The manufacturer assumes no responsibility for injury or damage caused by improper installations.
Version 08/06 - Page 5
