OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
WARNING: Always remove the power plug from the wall outlet before assembling or removing accessories.
Inserting The Handle Into The Main Unit
•Insert the handle into the hole on the top of the unit. Make sure that the slot in the handle fits correctly into the opening. (Fig. 1)
•Insert the sleeve nut into the unit first. Then holding the sleeve nut with your thumb, insert the bolt. Using a flat screw driver, secure the bolt to the sleeve nut. (Fig. 1)
•To remove the handle, you have to remove the bolt and the sleeve nut.
Attaching The Hose To The Main Unit
•Hold the end of the removable hose handle and insert it into the hose connector. (Fig. 3)
Hose
Connector
Fig. 3
Inlet
Hose
Cleaning the Filter Ring
1.Around the HEPA filter there is a filter ring. This is washable in lukewarm water.
(Fig. 16) To remove the filter ring, slide it off the HEPA filter.
2.We recommend washing the filter ring when you are
washing your HEPA filter. Always allow the
filter ring to air dry for 24 hours before replacing onto the HEPA filter. Never run the vacuum without all the filters in place.
Changing & Cleaning the Exhaust Filter
The exhaust filter is a rinseable filter but should be replaced every three (3) months.
Motor Thermostat
IMPORTANT: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:
• | Push the On/Off button once. |
• | Disconnect the plug from the |
| power source. |
• | Check the source of overheating |
| problem. (i.e. clogged hose or |
| filter) |
• If clogged hose or filter is found, | |
| unclog the hose and replace the |
| filters. |
• | Wait at least 45 minutes before |
| attempting to reuse the vacuum. |
• | After unit has cooled down for |
| 45 minutes, plug in the cleaner |
| and push the On/Off button. The |
Sleeve nut
Fig. 1
Bolt
Motorized
Floor Brush
Hose Connector
• To remove the exhaust filter covers, |
push the exhaust filter covers up. |
Remove the filter. (Fig. 17) |
• Rinse the exhaust filters in lukewarm |
water and air dry the filters completely |
for 24 hours. Do not use a washing |
vacuum should start again. |
• If the vacuum still does not start, |
contact customer service at |
1 (800) |
Attaching The Motorized Floor Brush To The Main Unit
Winding & Unwinding The Power Cord
machine to rinse the filters. Do not use |
a hair dryer to dry them. Air dry only. |
Never operate the vacuum without the |
•Insert the motorized floor brush into its location at the bottom of the main unit, in the direction of the arrow. (Fig. 2)
•Make sure that the motorized floor brush is firmly inserted into the floor brush socket.
•Insert the inlet hose into the floor brush hose connector that is on the floor brush. (Fig. 3)
Pin
Motorized Floor
Brush ReleaseMotorized Floor
Brush Hose
Connector
Fig. 2
This vacuum cleaner is equipped with a convenient cord storage feature. The power cord winds around the two cord holders at the back of the unit. The top one has a quick
cord release feature. Turn the cord hook to the left or the right to remove the power cord. (Fig. 4)
When using the vacuum, attach the power cord to the cord holder so that the power cord is out of the way when you
are vacuuming. (Fig. 5)
Fig. 5
Fig. 4
Cord holder
exhaust filters in place. |
• When the filters are |
dry, replace into |
the exhaust filter |
covers and replace |
on the vacuum. |
• Severely soiled or |
clogged filters should |
be thoroughly rinsed with |
fresh tepid water. A mild |
detergent can be used |
if required. |
Exhaust
Filter
Cover
Fig. 17
4
9
