Fantom Vacuum PT205H owner manual Assembly Instructions, Attaching the Vacuum Bag

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Assembly Instructions

WARNING: Remove the plug from the power source before

assembly of leaf blower. This will help prevent accidental starting of the unit which could result in serious injury.

CAUTION: The impeller rotates for a few seconds after you turn off the

7.Tighten the screws firmly but do not

over-tighten.

Note: If it is necessary to disassemble the leaf blower, follow these instructions:

8.	Turn the unit “Off” and remove the
	plug from the extension cord.
9.	Remove the two (2) self tapping
	screws from either side of the blower
	outlet housing.
10.	Remove the two (2) screws and nuts

3. Tighten the vacuum bag onto the	3. Fully extend the shoulder strap.
debris exhaust tube and fasten the	(Fig. 7)
velcro strap securely on top of the
ridge created for the bag cuff. (Fig. 4)

blower and will cause injury. WAIT until all parts stop moving.

NOTE: Instructions must be followed in order.

1.Remove all parts from the packaging.

2.Remove the nuts and screws provided from the packaging.

3.Insert the blower/vacuum tube all the way into the opening on the motor housing until the holes in the tabs on the blower/vacuum tube align with the screw holes in the housing. (Fig. 1)

holding the blower/vacuum tube to

the housing.

Note: Place the all the screws and nuts in a safe place for future use.

11. Remove the blower/vacuum tube from the motor housing.

Important: Always replace the blower/vacuum tube before using the leaf blower.

IMPORTANT: The leaf blower will not run unless the vacuum tube is locked in place.

Fig. 4	Debris Exhaust
	Tube

Vacuum Bag

4.To remove the vacuum bag, loosen the velcro strap and pull the vacuum bag off of the debris exhaust tube.

(Fig. 5)

Clip

Fig. 7

4.Attach the metal clip of the shoulder strap to the latch support on top of the handle. (Fig. 8)

Latch Support

Screw

Motor Housing

Nut

Attaching the Vacuum Bag

WARNING: Remove the plug from the power source before

Pull vacuum

bag down

Clip Fig. 8

5. Place the shoulder

Self-TappingSelf-Tapping

ScrewScrew

Screw

Nut

Fig. 1

Blower/Vacuum

Tube

4.Insert the two (2) screws into the right side of the motor housing the two (2) nuts into the left side of the motor housing. (Fig. 1)

5.Tighten the screws firmly. Do not over-tighten.

6.Insert the two (2) self-tapping screws into the holes on either side of the blower outlet housing. (Fig. 2 )

Air Intake (Vacuum)

assembly of leaf blower. This will help prevent accidental starting of the unit which could result in serious injury.

1.Slide the buckle that is on the vacuum bag onto the vacuum bag hook that is on the underside of the blower/vacuum tube. (Fig. 3)

Vacuum Bag Hook

Buckle

Fig. 3

2.Slide the vacuum bag over the debris exhaust tube on the housing. (Fig. 2)

Fig. 5

5.Always replace the vacuum bag before using the leaf blower.

Attaching the Shoulder Strap

If the shoulder strap is not already put together:

1.Push the end through the center of the buckle.

2.Pull the strap over the cross bar and down through the slot in the buckle. (Fig. 6)

strap over your

head and opposite

shoulder. (Fig. 9)

6. While in the

operating position,

adjust the length

of the shoulder

strap to fit your

height. To lengthen

the shoulder strap,

pull the strap down

and move he buckle Fig. 9 up. To shorten, pull

the strap back through the buckle while moving the buckle down. (Fig. 10)

Air Output

(Blower)

Fig. 2

Debris Exhaust

Tube

6

To Lengthen To Shorten

Fig. 6

Fig. 10

7