OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
CAUTION
When you wish to stop using the pressure washer temporarily, make sure that the safety lock has been engaged to avoid any accidental operation. (Fig. 14)
Fig. 14 | Safety | |
Lock | ||
|
Using the Adjustable Fan Jet lance
The angle of the water on the fan jet lance may be adjusted between 0° and 60° by turning the nozzle adjuster
&Fig. 16) Always make sure that the "On/Off' switch is in the "Off" position before changing the angle of the water jet. It is also recommended that the trigger gun safety lock be engaged as well. The adjustable fan jet lance allows you to use any variety of spray pattern from a full fan spray to a direct stream spray. When using the pressure washer to clean wood decks, siding vehicles, etc., always start using the fan spray and begin spraying from a minimum 36" away to avoid damaging the surface of the material that you are cleaning. Always clear the area that you will be cleaning of people, pets and objects.
Fig. 15 | Fig. 16 |
Using the High Pressure lance
The high pressure lance may be used alone (Fig. 17) or with the detergent applicator bottle.
Add detergent to the bottle and then attach the detergent applicator bottle to the high pressure lance, just push it on the end of the high pressure lance. (Fig. 18) To remove the detergent applicator bottle, lift the tab on the top of the connector and pull off.
Fig. 17
Fig. 18
Using the Brush With the Trigger Gun
The brush is used with the trigger gun. Push the brush onto the trigger gun nozzle and turn clockwise to lock as you would for the lances. (Fig. 19) the brush may be used for washing cars, boats, windows and other similar items. The brush operates at open orifice pressure so it will not direct a stream of water.
Fig. 19
Maintenance & Cleaning
Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed. Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 20). Remove periodically and inspect for any deposits that might accumulate there.
Hose Connector
Water Intake
Fig. 20
Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit "Off". Unplug from electric outlet and disconnect the water supply. Remove the lances, trigger gun and hose from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 21)
Fig. 21
Suitable Use of Your Pressure Washer
This high pressure washer is suitable for
The high pressure washer is suitable for washing with cold water only. The water that you use for the pressure washer must not be dirty, sandy or contain any corrosive chemical products.
The pressure washer may be used to wash shutters, doors, tiles, cars, decks, campers, etc., where high water pressure is necessary to remove dirt.
With the detergent applicator bottle, the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned .
When using the pressure washer we recommend the use of personal safety items to reduce the risk of accidental injury.
Unpacking Your Pressure Washer
After you open the package, check to make sure that all the parts are in the box as pre parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual. If you have any questions, call FANTOM customer service at
Correct Use of the Pressure Washer
•Place the pressure washer in a safe area and on a horizontal surface.
•When using the pressure washer, hold the trigger gun firmly with one hand on the handle and the other on the lance. (Fig. 1)
Fig. 1
•NEVER point the water jet at electric wiring, at the pump unit, or at any person or animal.
Assembling the Pressure Washer Trolley
1.Carefully take all the trolley parts and place together on a flat, stable surface.
2.Insert the two (2) legs into the support brackets and secure with the two (2) screws provided. (Fig. 2)
Fig. 2
3.Place the pressure washer between the two support brackets and secure with the two (2) screws provided.
(Fig. 3)
7
This will occur more frequently if your water supply is very hard.
Fig. 3
4