BASIC SHREDDING OPERATION
Continuous operation:
NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond
PAPER OR CD/CARD
1
disconnect power
switch in ON (I) position.
23 4 5
Press ( ) ON to | Feed into paper | To shred CDs rotate | Hold CD/card at edge, |
activate (blue) | entry and release | CD flap into place | feed into CD/Card flap |
|
|
| entry and release |
6
When finished shredding set to Off ()
JAM PROOF SYSTEM OPERATION
Eliminates frustrating jams by preventing overloads and powering through misfed paper.
1
23
If too many sheets, indicator will | Remove several sheets until the |
light up to red and shredder will | indicator is below red and the |
not take paper | shredder will take the paper |
MISFED PAPER
1
2
AUTO
Automatic correcting action will power through the misfed paper, so shredding can continue
3
Misfed paper can also be addressed by manually using forward and reverse (See Maintenance & Troubleshooting)
Feed into paper entry and release
23
If paper is misfed and stops shredding
2
3
Shredder will take fewer sheets, | Increase the number of sheets |
but if indicator is below yellow, | being fed up to the top yellow light |
you can add more sheets without | to maximize your productivity |
fear of jamming |
|
If there is too much paper for the shredder to power through, it will reverse the paper out for easy removal
Reduce paper quantity to an acceptable amount and refeed into paper entry
SAFESENSE® TECHNOLOGY OPERATION
Stops shredder immediately when hands are too close to the opening.
|
|
|
|
|
|
|
| FLASHING INDICATOR |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
| 2 |
| 3 |
|
|
| 1 |
|
|
|
| 2 |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Turn the shredder ON | Touch test area and | SafeSense® is active and | SafeSense® is deactivated when | Shift override switch to |
( ) to activate SafeSense® | look for the SafeSense® | working properly | indicator is flashing | the “active” position, |
| indicator to illuminate |
|
| reactivating SafeSense® |
3
Confirm the indicator is no longer flashing and retest by putting your hand on the test area