Fender 210 manual E n d e r 2 1 0 P ro L o u d s p e a k e r E n c l o s u re, Specifications

6 F e n d e r ® 2 1 0 P ro L o u d s p e a k e r E n c l o s u re

Your new 210 Pro Bass Loudspeaker Enclosure is con- structed from 3/4" (1.9 cm) 13-ply Baltic Birch Plywood and is capable of handling 350 Watts of continuous power. The 210 Pro features two 10" (25.4 cm) speak- ers with 59 oz (1.68 kg) magnets and is designed for use with Fender® Bassman® and Pro Series amplifiers or other professional quality bass amplifiers. Please read these instructions and the instructions that came with your amplifier before making connections. Follow all equipment caution and safety labeling.

SPECIFICATIONS

PART NUMBER:	22-17500-000
DRIVERS:	Two 10" (25.4 cm) Fender
	Special Design Cast Frame
	Woofers
	2" (5.1 cm) Voice Coil, 59 oz
	(1.68 kg) Magnet
	One Horn Tweeter

SPEAKER CONNECTIONS

Use 16 gauge (or heavier) speaker cable with one of the three types of input connections on your 210 Pro:

A)Phone jacks with a standard 1/4" plug

B)Binding posts with dual “banana” plug or stripped wires

C)Speakon® connector with Speakon® plug

Multiple 210 Pro cabinets can be linked as illustrated, when additional output is needed. Note: Follow the speaker impedance load guidelines set by the manufac- turer of your amplifier to avoid damage to your equip- ment.

	1" (2.5 cm) Voice Coil, 8 oz
	(0.23 kg) Magnet
CABINET:	3/4" (1.9 cm) 13-ply Baltic
	Birch Plywood
SENSITIVITY:	95 dB, 1 Watt - 1 Meter
POWER HANDLING:	350 Watts, Continuous
	700 Watts, Program
IMPEDANCE:	8Ω
CONNECTIONS:	Dual,	Parallel		Wired,	1/4”
	High	Current		Input Jacks,
	Binding		Posts		and
	Speakon® Connector

SERIAL NUMBER SERIAL NUMBER

POWER RATING	HORN		POWER RATING	HORN
350W CONTINUOUS			350W CONTINUOUS
700W PROGRAM	LEVEL		700W PROGRAM	LEVEL
		MODEL			MODEL
WARNING:			WARNING:
FENDER LOUDSPEAKER SYSTEMS			FENDER LOUDSPEAKER SYSTEMS
ARE CAPABLE OF PRODUCING	MIN.	MAX.	ARE CAPABLE OF PRODUCING	MIN.	MAX.
VERY HIGH SOUND PRESSURE			VERY HIGH SOUND PRESSURE
LEVELS WHICH MAY CAUSE			LEVELS WHICH MAY CAUSE
TEMPORARY OR PERMANENT			TEMPORARY OR PERMANENT
HEARING DAMAGE. USE CARE			HEARING DAMAGE. USE CARE
WHEN SETTING AND ADJUSTING			WHEN SETTING AND ADJUSTING
VOLUME LEVELS DURING USE.			VOLUME LEVELS DURING USE.

A PRODUCT OF:	A PRODUCT OF:
FENDER MUSICAL	FENDER MUSICAL
INSTRUMENTS CORP.,	INSTRUMENTS CORP.,
CORONA, CA U.S.A.	CORONA, CA U.S.A.
MADE IN MEXICO	MADE IN MEXICO

PARALLEL	PARALLEL
INPUTS	INPUTS
IMPEDANCE	IMPEDANCE
8Ω	8Ω

ENCLOSURE VOLUME:	VB = 3.2 ft3	(89 l)
DIMENSIONS:
Height:	16.5 in	(41.9 cm)
Width:	25.5 in	(64.8 cm)
Depth:	18.5 in	(47.0 cm)

HORN TWEETER

The horn tweeter is protected from power-overload damage by an incandescent lamp. If the horn tweeter stops responding, replace the lamp as you would a blown fuse. The lamp and a spare (reorder P/N 051857) are located on the circuit board on the inside of the input jack panel.

Lamp Replacement:

1)Remove the 4 screws from the input jack panel cor- ners.

2)Pull the panel out, then up.

3)Use a small flathead screwdriver to remove the blown lamp which is visible through a cutout in the circuit board.

4)Remove the spare lamp stowed on the side of the circuit board and install it where the blown lamp was located.

5)Install the input jack plate in the reverse order of removal.

WEIGHT: 61 lb (27.7 kg)

Product specifications are subject to change without notice.

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORP.

CORONA, CA USA

Fender® is a registered trademark of FMIC, Speakon® is a registered trademark of Neutrik. Copyright © 2003 FMIC

www.f e n d e r.com ✧ www. m r g e a r h e a d .net