Fender 410 PRO manual Speaker Connections, Horn Tweeter, Specifications

6 F e n d e r ® 4 1 0 P ro S L L o u d s p e a k e r E n c l o s u re

Your new 410 Pro SL Bass Loudspeaker Enclosure is constructed from 3/4" (1.9 cm) 7-ply Birch/Maple Plywood and is capable of handling 300 Watts of con- tinuous power. The 410 Pro SL features four 10" (25.4 cm) speakers with 44 oz (1.25 kg) magnets and is designed for use with a Fender® 800 Pro, Bassman® 1200, Bassman® 300, Bassman® 400 Head or other professional quality bass amplifier. Please read these instructions and the instructions that came with your amplifier before making connections. Follow all equipment caution and safety labeling.

SPEAKER CONNECTIONS

Use 16 gauge (or heavier) speaker cable with one of the three types of input connections on your 410 Pro:

A)Phone jacks with a standard 1/4" plug

B)Binding posts with dual “banana” plug or stripped wires

C)Speakon® connector with Speakon® plug

Multiple 410 Pro SL cabinets can be linked as illustrat- ed, when additional output is needed. Note: Follow the speaker impedance load guidelines set by the manufac- turer of your amplifier to avoid damage to your equip- ment.

HORN TWEETER

The horn tweeter is protected from power-overload damage by an incandescent lamp. If the horn tweeter stops responding, replace the lamp as you would a blown fuse. The lamp and a spare (reorder P/N 051857) are located on the circuit board on the inside of the input jack panel.

Lamp Replacement:

SPECIFICATIONS

PART NUMBER:	2217000000
DRIVERS:	Four 10" (25.4 cm) Fender
	Special Design Cast Frame
	Woofers
	2" (5.1 cm) Voice Coil, 44 oz
	(1.25 kg) Magnet
	One Horn Tweeter
	1" (2.5 cm) Voice Coil, 8 oz
	(0.23 kg) Magnet
CABINET:	3/4" (1.9 cm) 7-ply
	Birch/Maple Plywood
SENSITIVITY:	94 dB, 1 Watt - 1 Meter
POWER HANDLING:	300 Watts, Continuous
	600 Watts, Program
IMPEDANCE:	8Ω
CONNECTIONS:	Dual,	Parallel		Wired,	1/4”
	High	Current		Input Jacks,
	Binding		Posts		and
	Speakon® Connector
ENCLOSURE VOLUME:	VB =	4.4 ft3	(125 l)
DIMENSIONS:
Height:	25.5 in		(64.8 cm)
Width:	25.5 in		(64.8 cm)
Depth:	18.5 in		(47.0 cm)
WEIGHT:	78 lb		(35.5 kg)

Product specifications are subject to change without notice.

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORP.

CORONA, CA USA

1)Remove the 4 screws from the input jack panel cor- ners.

2)Pull the panel out, then up.

3)Use a small flathead screwdriver to remove the blown lamp which is visible through a cutout in the circuit board.

4)Remove the spare lamp stowed on the side of the circuit board and install it where the blown lamp was located.

5)Install the input jack plate in the reverse order of removal.

Fender® and Bassman® are registered trademarks of FMIC,

Speakon® is a registered trademark of Neutrik.

Copyright © 2003 FMIC

www.f e n d e r.com ✧ www. m r g e a r h e a d .net