• Pencil
• Drill with 3/16” (5 mm) drill bit
• Phillips screwdriver

HOW TO INSTALL THIS SMOKE ALARM

THE PARTS OF THIS SMOKE ALARM

1. Test/Silence button

2. Battery drawer

3. Power indicator LED

4. Smoke Alarm LED

QUICK INSTALLATION INSTRUCTIONS

1. Insert the batteries into the battery drawer of the first Alarm and close the drawer.

2. The Alarm will sound with a chirp.

3. If you purchased the Talking Smoke and Carbon Monoxide Alarm, you will now be prompted to set the Alarm's location.

Follow the direction given by the Alarm.

NOTE: Steps 4 through 6 need to be completed within two minutes. If more than two minutes pass, the Green power LED will stop blinking. Simply open the battery drawer of the second Alarm and repeat steps 4 through 6.

4.Insert the batteries into the battery drawer of the next Alarm.

DO NOT CLOSE THE DRAWER.

5.Press and hold the test button and then close the battery drawer.

6.Once you hear the unit chirp, release the test button. The Green power LED will start to blink indicating the ONELINK® Alarm is waiting for program data from one of the other setup ONELINK® Alarms.

7.Press and hold the test button on the first Alarm, until the second Alarm chirps and its Green power LED stops blinking. Then release the test button.

8.If you purchased a Talking Smoke Alarm, you will now be prompted to set the Alarm's location. Follow the directions given by the Alarm.

9.If you have purchased the hardwired battery back-up ONELINK® Alarm, you can now connect the hardwired Alarm by installing the three-wire connector on the ceiling to the Alarm.

10.Repeat steps 4-9 for additional ONELINK® Alarms.

You have now successfully linked your new ONELINK® Alarms. To add additional Alarms at a later time, follow steps 4 through 9.

TOOLS YOU WILL NEED:

This unit is designed to be mounted

on the ceiling, or on the wall if necessary.

• Hammer

• Pliers to activate optional “tamper-resistant” locking features

FOLLOW THESE SIMPLE STEPS!

If you want to lock the battery drawer, or lock the Smoke Alarm to the mounting bracket, please read the “Optional Locking Features” section before you begin installation.

1.Hold base firmly and twist the mounting bracket counterclockwise to separate it from the base.

2.Hold the mounting bracket against the ceiling (or wall) so the vertical mounting slot is aligned in the 12 o’clock position and trace around the inside of the mounting slots (vertical and horizontal mounting).

3.Put the unit where it won’t get covered with dust when you drill the mounting holes.

4.Using a 3/16” (5 mm) drill bit, drill a hole through the center of the oval outlines you traced.

5.Insert the plastic screw anchors (in the plastic bag with screws) into the holes. Tap the screw anchors gently with a hammer, if necessary, until they are flush with the ceiling or wall.

6.Line the mounting bracket up

over the plastic screw anchors.

7. Screw the mounting bracket to the ceiling or wall through the mounting slots using the two screws provided.

8.Attach the Smoke Alarm to the mounting bracket. Line up the guides on the alarm’s base with the guides on the mounting bracket. When guides are lined up, turn the base clockwise (right) until it snaps into place.

NOTE: Once the Smoke Alarm is snapped onto the mounting bracket, you can rotate the Smoke Alarm to adjust the align- ment.

9.Test the Smoke Alarm. See “Weekly Testing.”

2

Page 1 Page 3
Page 2
Image 2
First Alert SA500 user manual HOW to Install this Smoke Alarm, Parts of this Smoke Alarm, Quick Installation Instructions
Page 1 Page 3

SA500 specifications

The First Alert SA500 is a highly reliable combination smoke and carbon monoxide detector designed to provide early warning for both smoke and gas hazards in residential settings. This advanced device incorporates several state-of-the-art technologies and features to ensure the highest level of safety for you and your family.

One of the most notable features of the SA500 is its dual-sensor technology. It uses both photoelectric and ionization sensing technologies, which enhances its ability to detect a wide range of fire types, including smoldering fires and fast-flaming fires. This dual approach means that users can enjoy greater peace of mind knowing that they are protected from a variety of potential dangers.

In addition to smoke detection, the SA500 is also equipped with a carbon monoxide (CO) sensor. Carbon monoxide is an odorless and colorless gas that can be extremely dangerous, making the inclusion of CO detection an essential feature for any home's safety system. The detector continuously monitors the air for CO levels and provides an immediate alarm if dangerous concentrations are detected.

Another key characteristic of the First Alert SA500 is its easy-to-read digital display. This feature shows real-time updates on the concentration of carbon monoxide in the environment, making it user-friendly and informative. The display also indicates the status of the smoke detector, ensuring that users can easily tell if the device is functioning correctly.

The SA500 is designed with a long-lasting battery backup, ensuring that it remains operational even during power outages. This is crucial for maintaining safety, as smoke and CO detectors must be functional at all times. The device is easy to install, with a sleek and modern design that blends seamlessly into any home decor.

Furthermore, the SA500 features a voice alarm that announces the type of danger detected, whether it is smoke or carbon monoxide. This distinct feature helps users respond quickly and appropriately in emergencies, differentiating between potential fire hazards and carbon monoxide dangers.

Overall, the First Alert SA500 combines advanced technologies and user-focused features to deliver comprehensive protection against both smoke and carbon monoxide. Its reliability, dual-sensor technology, and informative display make it an essential addition to any home safety plan, ensuring you and your loved ones are well-protected from potential hazards.
Top Page Image Contents