Fisher & Paykel OB60SL9DEX Using The Timer, For More Info, Fit Both Catalytic Panels, First Use

FIRST USE

4 FIT BOTH CATALYTIC PANELS

Place each catalytic panel flush against the side wall, noting the position of the cutouts for the lamp and lock nuts

Catalytic panel

5 REPLACE BOTH SIDE RACKS

To replace the side racks, locate the top of the side rack into the two upper lock studs and gently push the retaining wire back under the lower lock stud.

1 1

lock stud

retaining wire

2

7 CONDITION THE OVEN

TEMPERATURE FUNCTION

7 Leave the temperature at 200 oC		8 When you have finished, turn the function dial to
	for 5 minutes.	Off . The halos will go out.
	The halo will remain white.

There will be a distinctive smell and a small amount of smoke during the conditioning process as manufacturing residue is burnt off. This is normal, but make sure the kitchen is well ventilated during the conditioning.

Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.

USING THE TIMER

6 REPLACE SHELVING

To replace a wire shelf, check the guard rail (as shown) to make sure the shelf is the right way up. slide it horizontally back along the side racks ensuring it is level and the stop notch is facing down.

To replace a telescopic sliding shelf, position it so that the front bar is toward you, as shown. Check that the sliding frame is not extended.

Check the guard rail (as shown) to make sure the shelf is the right way up.

Position the shelf so that it is level and the rear shelf tag at the back of the sliding frame rests behind the side rack wire (as shown). Then push the sliding shelf all the way to the back of the oven, until the front shelf tag drops into place behind the side rack wire.

For your safety, the wire shelves and telescopic sliding frames are built together as one unit and are not separable. This means that when placed properly on the side racks, the slides will prevent the wire shelves from tilting when pulled towards you.

To prevent the tags from lifting off the side racks, take care to slide the shelves forward horizontally.

Guard rail

You can use the timer at any time, even if you are not using the oven.

If the time is more than an hour, the display will count down in minutes (hr:min). If it is less than an hour, it will count down in seconds (min:sec). You can set the timer for up to 23 hours 59 minutes.

Important!

The timer does NOT turn the oven off.

Stop Notch Front bar

Guard rail

1Select the timerby pressing

the right scroll button once. The timerindicator will appear and the colon will flash.

To modify the timer setting

2 Press the select		button to	3 Set the time by pressing the			4 Press the select		button to
	confirm.			scroll	buttons.		confirm.
	The display will flash to indicate			Holding the buttons down			The timer will then begin to
	the timer is ready to be set.			will speed up the scrolling.			count down.
							If you want to check the time
							of day, press the cancel

button once.

Press the right scroll button to scroll back to the timer.

	Front shelf tag	Rear shelf tag
Replacing a wire shelf	Replacing a telescopic sliding shelf

7 CONDITION THE OVEN

It is important to condition your oven before using it for cooking and baking. Conditioning will burn off any manufacturing residues and ensure that you get the best results right from the start.

1Make sure you have removed ALL the cable ties used to secure the shelving during transit.

2 Make sure you have set the clock.

3 Make sure all the shelves are fitted.

1Make sure the display shows the remaining time counting down.

2 Press the select button.

3 Press the scroll buttons to set a new time. 4 Press the select button to confirm.

To cancel the timer setting

1Make sure the display shows the remaining time counting down.

2Press the cancel button until the display shows the time of day and the timerindicator disappears.

When the set time is up

The display will show 0:00 and a tone will sound every 15 seconds.

Press any button to stop the tone sounding. The display will revert to showing the time of day.

FUNCTION TEMPERATURE TEMPERATURE FUNCTION

4 Select the Bake function.		5 Set the temperature to 200 oC for 30 minutes.		6 After 30 minutes is up,
	The halo will glow white.		While the oven is heating up, the temperature halo	select the Fan Grill function.
	Each function has a preset		will glow red and the temperature indicator will
	temperature and so the oven		alternately show the actual and set temperatures.
	will start heating at the Bake		When the oven has reached set temperature, a tone
	preset temperature of 180 oC.		will sound and the halo will turn white.

FOR MORE INFO

For detailed information on the other features of your oven

For warranty information

If you…

have any questions or comments

need a Fisher & Paykel authorized technician to service your product

need replacement parts or accessories want to register your product

see your ‘User guide’

see your ‘Service and warranty’ booklet

see your ‘Service and warranty’ booklet or contact us

NZ	toll-free, 24/7	0800 372 273
AU	toll-free, 24/7	1300 650 590
GB	toll-free, 24/7	0845 066 2200
IE	toll-free, 24/7	1800 625 174
www.fisherpaykel.com		590479A	12.12