Stereo Power Amplifier
MA–S160
Owner’s Manual
Thank you for purchasing theIn order to use the product in a safe manner, please read this Owner’s
Manual thoroughly before using.Also, keep this manual for future reference. Accessory ChecklistBefore proceeding with the setup, make sure that the following accessory is included in the package.
If it is missing, please contact the dealer whom you purchased the amplifier from, or Flying Mole Corp.
• AC Power Cable x 1 | • Remote Connection | • Remote Power Control | • Owner's Manual | ||||||||||||||||
|
|
|
|
|
|
|
|
| Cable (2m) x 1 | Connector x 2 | (this booklet) x 1 | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
THIS SYMBOL INDICATES THAT DANGEROUS | THIS SYMBOL INDICATES THAT THERE ARE IMPOR- |
VOLTAGE CONSTITUTING A RISK OF ELECTRIC | TANT OPERATING AND MAINTENANCE INSTRUC- |
SHOCK IS PRESENT WITHIN THIS UNIT. | TIONS IN THE OWNER’S MANUAL WITH THIS UNIT. |
|
|
WARNING : To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
■The important safety instructions
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli- fiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
THE APPARATUS IS NOT WATERPROOF. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT PUT ANY WATER SOURCE NEAR THIS APPARATUS, SUCH AS VASE, FLOWER POT, COSMETICS CONTAINER AND MEDICINE BOTTLE, ETC.
IMPORTANT NOTICEIf this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures :
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Flying Mole Corporation.
2 Features
Component Names
●Independent power twin monaural construction
●Utilizing our original
●Fixed level (volume bypass) and Variable level are selectable
●Connect the amplifier in bridge (BTL) connection to use it as a 300W/8Ω mono bloc power amplifier
●Gorgeous parts for uncompromising standards
3 Component Names
■Front Panel
q | w |
q Power Switch / Power Indicator | w LEVEL Adjustment Knobs |
Used to turn the amplifier's power ON or OFF. | Controls the input signal level. |
The indicator lights when the power is turned ON. | Setting the knob to "MIN" turns down the level to |
| the minimum. |
| These knobs don't work when the Mode switch t |
eREMOTE POWER CONTROL Jacks
●OUT
Remote output jacks used to interlock the power on another device with the activation/deactivation of the power on the amplifier.
Connect these jacks to a Flying Mole product equipped with remote power control input jacks.
●IN
Remote input jacks used to interlock the power on the amplifier with the activation/deactivation of the power on another device.
Connect these jacks to a Flying Mole product equipped with remote power control output jacks.
Turn “OFF” the power switch of the amplifier to use the amplifier with cables connected to these jacks.
*Refer to the owner's manuals of the devices to be connected as well.
*These jacks cannot be used with products from other manufactures or for other purposes than the
rSPEAKER Connectors (* Be sure to check po-
larity before connection)
Used to connect the amplifier to the speaker. Connect one each speaker to the [RIGHT] and [LEFT] connectors when the Mode switch t is set to "FIXED" or "VARIABLE".
Make sure that the speaker's impedance is between 4 ohms and 16 ohms.
Connect one speaker to the two outermost connec- tors of the four [RIGHT] and [LEFT] connectors when the Mode switch t is set to "MONO/BTL".
Make sure that the speaker's impedance is between 8 ohms and 16 ohms.
Refer to the “r Connections” for details.
●FIXED (Switch position: Right)
The amplifier works as a stereo power amplifier (100W/8 ohms x 2 CH). Use the INPUT jacks (FIXED) y as input jacks.
The LEVEL adjustment knobs w on the front panel are bypassed and inoper- able.
●MONO/BTL (Switch position: Left)
The amplifier works as a monaural am- plifier in BTL mode (300W/8 ohms x 1 CH). Use the [R] jack of the INPUT jacks (VARIABLE) y as the input jack.
The input signal level can be adjusted with the [RIGHT] knob of the LEVEL adjustment knobs w on the front panel.
yINPUT Jacks (VARIABLE)
Used to connect the input signal to the amplifier. Connect the jacks to the OUTPUT jacks on the pream- plifier, etc.
One each cable can be connected to the [R] and [L] jacks when the mode switch áD is set to "VARIABLE". Connect only the [R] jack when the mode switch áD is set to "MONO/BTL". These jacks are not to be used when the mode switch áD is set to "FIXED".
uINPUT Jacks (FIXED)
Used to connect the input signal to the amplifier. Connect the jacks to the OUTPUT jacks on the pream- plifier, etc.
One each cable can be connected to the [R] and [L] jacks when the Mode switch t is set to "FIXED". These jacks are not to be used when the Mode switch t is set to "VARIABLE" or "MONO/BTL".
is set to "FIXED". When the Mode switch t is set to |
"MONO/BTL", only the [RIGHT] knob will work . |
■Rear Panel
e | r | t y u | r | i |
tMode switch
Used to switch the operation mode of the amplifier. Select one of the following settings according to the connection.
●VARIABLE (Switch position: Center)
The amplifier works as a stereo power amplifier (100W/8 ohms x 2 CH). Use the INPUT jacks (VARIABLE) y as in- put jacks.
The input signal level can be adjusted with the LEVEL adjustment knobs w on the front panel.
iAC IN Jack
Used to connect the supplied AC power cable to the amplifier.
Connect the other end of the AC power cable to household AC outlet.