Flymo Multi-Trim manual SPOOL CAP AND NYLON LINE 2 LINES - T, Caring For Your Multi Trim, English

SPOOL CAP AND NYLON LINE (2 LINES) - T

T1-a - Cap, T1-b - Cap Release Latch, T1-c - Spool,						6.	Repeat for second line.
T1-d - Spoolholder, T1-e - Slot,						•	Ensure spool is fully located by gently rotating it
T2-a - Upper Section,			T2-b - Lower Section				during fitment, whilst keeping the spoolholder
To remove spool cap							steady.
1. Press and hold in the two cap release latches.					(T1).	7.	Refit the cap.
2.	Pull cap away from the spoolholder.			(T1).		To fit nylon line only:
When refitting the spool cap						•	Remember! Your Flymo Trimmer is designed to
1. Keep all areas of the cap and spoolholder clean.							use only nylon line with a maximum diameter of
	Failure to do so may prevent the cap being securely						1.5mm. Use only genuine Flymo nylon line.
	located in the spoolholder.					1.	IF YOU HAVE TWO LINES FITTED
2.	Replace the cap,	pressing firmly DOWN towards					IMPORTANT - If your trimmer has 2 lines fitted
	the spoolholder to ensure cap is fully located.						always wind the line onto the upper section of
3. Check that the cap is correctly fitted by trying to							the spool first.
	remove it without depressing the two latches.						Take approximately 5 metres of line. Insert 15mm of
To replace nylon line.							line into one of the holes in the upper section of the
For your convenience it is recommended you buy spool							spool (T2) and wind line in the direction of the
and line complete. Nylon line only is also available.				Both			arrows on the top of the spool. Leave
are available from Electrolux Outdoor Products stockists.							approximately 100mm of line unwound and place
To fit spool and line complete:							into cleat as illustrated in figure	T3. Repeat on
1.	Remove the cap.						lower section of spool.
2.	Remove old spool.					2. Care should be taken to ensure that the line is
3.	Place spool into spoolholder.						neatly coiled on the spool. Failure to do so will
4. Release line from cleat (if 2 lines are fitted release							impair the efficiency of the automatic line feed.
	only one line).					3.	Then fit spool as described in	‘To fit spool and line
5.	Secure line into slot		(T1).				complete’, section above.

CARING FOR YOUR MULTI TRIM

After you have finished using your Flymo Multi-Trim follow the procedure below:

•AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM MAINS AND KEEP FEET AWAY FROM THE SWITCH LEVER WHEN:- CLEANING AROUND THE INSIDE OF THE SAFETY GUARD, REMOVING OR REFITTING SPOOL CAP, MANUALLY FEEDING

OR REPLACING NYLON LINE. (SEE FIGS U & V)

1.Disconnect from the mains electricity supply.

2.Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth.

3.Using the scraper provided (Multi Trim 200), clean around the inside of the safety guard to remove

any grass and debris. (Fig W).

4.Using a soft brush, clean around the inside of the safety

guard, the cutting head and the motor housing. (Fig X).

5.Inspect the trimmer carefully, especially the parts of the cutting head.

6.If your trimmer is damaged in any way contact your local

Electrolux Outdoor Products approved service centre.

•Never use a damaged trimmer.

7.Wind cable carefully to avoid kinking.

8.Store in a cool, dry place and out of reach of children.

ENVIRONMENTAL INFORMATION

Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to

company procedures, and with the potential for recycling at the end of the products’ life.

•Packaging is recyclable and plastic components have

been labelled (where practical) for categorised recycling.

•Awareness of the environment must be considered when disposing of ‘end-of-life’ product.

•If necessary, contact your local authority for disposal information.

SERVICE RECOMMENDATIONS

•Your product is uniquely identified by a silver and black product rating label.

•We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.

GUARANTEE AND GUARANTEE POLICY

If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing:

(a)The fault is reported directly to the Authorised Repairer.

(b)Proof of purchase is provided.

(c)The fault is not caused by misuse, neglect or faulty adjustment by the user.

(d)The failure has not occurred through fair wear and tear.

(e)The machine has not been serviced or repaired, taken apart or tampered with by any person not authorised by Electrolux Outdoor Products.

(f)The machine has not been used for hire.

(g)The machine is owned by the original purchaser.

(h)The machine has not been used outside of the country for which it was specified.

(i)The machine has not been used commercially.

*This guarantee is additional to, and in no way diminishes the customers statutory rights.

Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine:

Failures not covered by guarantee

*Replacing Nylon Line.

*Failures as a result of not reporting an initial fault.

*Failures as a result of sudden impact.

*Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.

*Machines used for hire are not covered by this guarantee.

*The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Nylon Line, Electric Mains cable.

*Caution!

Electrolux Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way.

ENGLISH - 4