Removing and Fitting the Cutting Chain

Important

Ensure that the Sabre Saw is switched off and disconnected from the Power Pack

Always wear gloves when removing or fitting the cutting chain.

Use only a guide bar with bar tip designed for this product.

In order to prevent kickback, do not remove the bar tip or replace the guide bar with one without a bar tip.

Removing the Cutting Chain

1.Loosen the screws (K1) on the sprocket guard (K2) with a screwdriver and remove the sprocket guard.

2.Loosen the hex socket head bolt (L1) with the hexagon drive tool provided and remove the bolt (L1)

and spacer washer (L2).

3. Push the guide bar (L3) against the tension adjusting spring (L4) and remove the guide bar and chain.

Fitting the Cutting Chain

1.Fit the chain over the guide bar with the bar tip upermost (M1), ensuring that the cutters are facing the revolving direction (M2)

2.Fit the chain over the sprocket (N1) and fit the concave end of the guide bar against the tension adjusting spring (N2).

3.Insert the hex socket head bolt (L1) through the spacer washer (L2), and guide bar (L3) and tighten with the hexagon drive tool provided, ensuring the guide bar is secure.

4.Fit the sprocket guard (K2) and tighten the screws (K1) ensuring the sprocket guard is secure.

Sharpening the Cutting Chain

Ensure that the Sabre Saw is switched off and disconnected from the Power Pack

Always wear gloves when sharpening the cutting chain

SHARPEN THE CUTTING CHAIN TO THE SPECIFICATIONS ILLUSTRATED IN PICTURE T

Filing the cutters

1.Use a round file 4mm in outer diameter to file the cutters. Apply it to the cutter so that it will be angled 30 degrees to the guide bar and protrude 1/5 of the

outer diameter from the tip of the cutter. Hold the file level and push it away from you while filing. Be careful not to touch the cutters with the file when pulling it back toward you.

Filing the depth gauges

1.Use a flat file to file the depth gauges. Hold the file level while filing. Round off the front corner of the

depth gauge to maintain its original shape.

Immerse the cutting chain in oil and wash off any filing chips and sawdust.

Environmental Information

Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life.

Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.

Awareness of the environment must be considered when disposing of ‘end-of-life’ product.

If necessary, contact your local authority for disposal information.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.

Service Recomendations

Your product is uniquely identified by a silver and black product rating label.

We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.

Guarantee and Guarantee Policy

If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing:

(a)The fault is reported directly to the Authorised Repairer.

(b)Proof of purchase is provided.

(c)The fault is not caused by misuse, neglect or faulty adjustment by the user.

(d)The failure has not occurred through fair wear and tear.

(e)The machine has not been serviced or repaired, taken apart or tampered with by any person not authorised by Husqvarna Outdoor Products.

(f)The machine has not been used for hire.

(g)The machine is owned by the original purchaser.

(h)The machine has not been used commercially.

*This guarantee is additional to, and in no way diminishes the customers statutory rights.

Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine:

Failures not covered by guarantee

*Failures as a result of not reporting an initial fault.

*Failures as a result of sudden impact.

*Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.

*Machines used for hire are not covered by this guarantee.

*The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Bar and chain

*Caution!

Husqvarna Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Husqvarna Outdoor Products, or by the machine having been modified in any way.

ENGLISH - 2

Page 5
Image 5
Flymo Sabre Saw instruction manual Environmental Information, Service Recomendations, Guarantee and Guarantee Policy

Sabre Saw specifications

The Flymo Sabre Saw is a versatile and innovative gardening tool designed for effortless cutting and trimming of various materials in your garden. Known for its lightweight design and ease of use, the Flymo Sabre Saw is perfect for both amateur and professional gardeners.

One of the standout features of the Flymo Sabre Saw is its powerful motor, which allows for quick and efficient cutting through branches, shrubs, and other garden waste. This electric saw is equipped with a sharp, high-quality blade that delivers clean cuts, minimizing damage to plants and ensuring a smooth finish. The blade can be easily changed, allowing users to switch between different blades for various tasks, whether it be pruning or cutting thicker branches.

The ergonomic design of the Flymo Sabre Saw ensures user comfort during extended use. Its lightweight construction reduces fatigue, while the soft-grip handle provides a secure and comfortable grip, enhancing control and precision while cutting. This makes it an ideal tool for users of all ages.

Another notable characteristic of the Flymo Sabre Saw is its safety features. The saw is equipped with a safety switch that prevents accidental activation, ensuring peace of mind during use. Additionally, the saw's compact size allows for easy maneuverability in tight spaces, such as between shrubs or in flower beds, allowing users to achieve precision cuts without hassle.

The technology employed in the Flymo Sabre Saw includes an innovative anti-jamming system that helps prevent the blade from getting stuck, enabling continuous cutting performance. It is also designed to operate quietly, making it suitable for residential areas where noise may be a concern.

Easy storage is another significant advantage of the Flymo Sabre Saw. Its compact design allows it to be stored without taking up much space, and many models come with a built-in hanging hook for simple storage solutions in sheds or garages.

In summary, the Flymo Sabre Saw combines powerful performance with user-friendly features, making it an essential tool for anyone looking to maintain their garden. With its cutting-edge technology, ergonomic design, and safety features, it stands out as a reliable choice for cutting tasks of all sizes. Whether you're pruning hedges or tackling larger branches, the Flymo Sabre Saw provides the efficiency and precision needed to keep your garden looking its best.