Frigidaire 134305700B Washer does not start, Washer wont spin, Residue left in drum, Water leaks

OCCURRENCE			POSSIBLE CAUSE / SOLUTION
	OPERATING
	Washer does not start.		• Electrical power cord may not be plugged in or connection may be loose.
			Make sure plug fits tightly in wall outlet.
			• House fuse blown, circuit breaker tripped, or a power outage has occurred.
			Reset circuit breaker or replace fuse. Do not increase fuse capacity. If
			problem is a circuit overload, have it corrected by a qualified electrician. If
			problem is a power outage, call local electric company.
			• Water supply faucets are not turned on. "F03" is displayed.Turn on water
			supply faucets.
			• Motor is overheated. Washer motor will stop if it becomes overheated. It will
			automatically restart after a cool down period of up to 30 minutes (if washer
			has not been manually turned off).
			• Dispenser drawer is not completely closed. Close dispenser drawer.
			• Washer door is not completely closed. "dr" (door open" is displayed.Close
	Washer won't spin.		door completely.
			• Dispenser drawer is not completely closed. "d:do" (dispenser door) is
			displayed. Close dispenser drawer.
			• Load is too small. Add 1 or 2 similar items to help balance the load.
	Residue left in drum.		• Heavily soiled items. Wipe drum with a nonabrasive household cleanser,
			then rinse. Shake or brush excess dirt and sand from items before washing.
	WATER		• This is a result of the siphoning action and is part of the normal operation of
	Water collects in bleach and fabric
			the washer. Water may be removed by removing the dispenser drawer (see
	softener compartments.
			Page 10, Figures 1 and 2) and draining water into the empty drum or sink.
		Wash load too wet after spin.	• Washer is overloaded. Do not overload washer. See Washing Procedures.
			• Load is too small. Add 1 or 2 similar items to help balance the load.
			• Load is out of balance. Rearrange load to allow proper spinning.
			• Drain hose is kinked. Straighten drain hose.
		Water does not enter washer or it	• Water supply is not adequate in area. "F03" is displayed. Check another
		enters slowly.	faucet in the house. Wait until water supply and pressure increase.
			• Water supply faucets are not completely open. "F03" is displayed. Fully open
			hot and cold faucets.
			• Water is being used elsewhere in the house. Water pressure must be at least
			30 psi (260 kPa). Avoid running water elsewhere while washer is filling.
			• Water inlet hoses are kinked. Straighten hoses.
	Warm or hot water is not hot enough.		• Hot water heater is set too low or is a distance from washer. Measure hot
			water temperature at nearby faucet with candy or meat thermometer. Water
			temperature should be at least 120°F (49°C). Adjust water heater as
			necessary.
			• Hot water is being used elsewhere in the house. Avoid using hot water
			elsewhere before or during washer use. There may not be enough hot water
			available for proper cleaning. If problem persists, your hot water system may
			be unable to support more than 1 use at a time.
		Water in washer does not drain or	• Drain hose is kinked or clogged. Clean and straighten the drain hose.
		drains slowly.	• Maximum standpipe height is 8' (2.4 m).
		Water leaks.	• Fill hose connection is loose at faucet or washer. Check and tighten hose
			connections. Install rubber sealing washers provided.
			• House drain pipes are clogged. Unclog drain pipes. Contact plumber if
			necessary.
			• Oversudsing. Use less detergent.
		Incorrect wash and rinse	• Hot and cold water hoses are connected to wrong supply faucets. Connect
		temperatures.	hot water hose to hot water faucet and cold water hose to cold water faucet.
		Water is entering washer but tub does	• Drain hose standpipe is incorrect height. Standpipe must be a minimum of
		not fill.	23.6" (60 cm) high to prevent siphoning. See INSTALLATION
			INSTRUCTIONS.

12