Frigidaire 650 Series warranty Connecting and Disconnecting the Portable/ Convertible Dishwasher

Connecting and Disconnecting the Portable/ Convertible Dishwasher

The portable/convertible dishwasher must be connected to a faucet and electrical outlet each time it is used. Follow directions on this page to properly connect dishwasher.

Faucet Adapter Assembly

For Outside	For Inside
	Threaded
Threaded	Faucet
Faucet	Use
Use Thin	Thick
	and
Washer	Thin
Only	Washers
Adapter	Two Brass
(Dual	Screens
Thread)	should be
	below the
	rubber
	washers

Connecting the Portable Faucet Adapter Assembly

Collar

Coupler

IMPORTANT: Make sure door is latched before moving dishwasher. The power cord, faucet coupler and hoses are located in a compartment in back of dishwasher. A special adapter must be installed on faucet before you can connect dishwasher.

1.Remove faucet adapter assembly from literature package.

2.Unscrew existing sink faucet aerator.

3.Check faucet spout to see if threads are inside or outside.

•If threads are on inside of faucet spout, use both thick and thin rubber washers.

•If threads are on outside of faucet spout, use thin rubber washer only.

•If faucet has no threads, an adapter kit with instructions for attachment to a non-threaded spout is available at most hardware stores.

4.Assemble faucet spout as shown. Make sure the two brass screens are located below the rubber washers.

Connecting the Portable/Convertible Dishwasher

1.Run water at faucet until it is hot. Turn off faucet.

2.Pull hoses out of compartment.

3.Push collar down and slip faucet connector onto faucet adapter.

4.When connector snaps into place, release collar.

5.Slowly turn on hot water all the way.

6.Plug power cord into grounded outlet.

Getting Water While Dishwasher is Running

You can get water from the faucet while the dishwasher is connected. However, avoid getting water when the dishwasher is filling or draining.

1.Press red button on coupler to get the water you want. The faucet is set on hot, adjust faucet if you want cold.

2.Be sure hot water is turned back on all the way to complete cycle.

Avoid fire hazard or electrical shock. Do not use an adapter plug, extension cord or remove grounding prong from electrical power cord.

Failure to follow this warning can cause serious injury, fire or death.

Power supply cord with 3-prong

grounding plug

Disconnecting the Portable/Convertible Dishwasher

1.When cycle has finished, turn off hot water.

2.Press red button on coupler to release water pressure being careful not to release coupler.

3.Press down on collar to release coupler.

4.Empty remaining water from coupler and return it to compartment.

5.Unplug power cord and return it to compartment.

IMPORTANT: A sink spray attachment hose can burst due to constant water pressure while in use. If your spray hose is installed on same water line as the dishwasher, we suggest you disconnect the sink spray attachment and plug the hole.

Electrical Connection for a Portable/Convertible Dishwasher

An electrical supply of 120 volts, 60 Hz, AC only, 15 amps is required. For your safety, the dishwasher must be grounded. If there is a malfunction or breakdown, grounding will reduce risk of electrical shock. This dishwasher has a power cord with a 3-prong grounding plug. It must be plugged into a mating 3-prong grounding type receptacle, installed and grounded in accordance with the National Electrical Code and any local codes and ordinances.

Grounding type wall receptacle

Do not under any circumstances cut, remove or bypass the grounding prong from this plug.

Converting to Built-In

Your portable dishwasher can be converted to a built-in (undercounter) model. A conversion kit No. 154241302 is required and is available from your local dealer or distributor. Instructions are included with the kit.

12