Installation Instructions
Installation Instructions |
| |
(continued) |
| |
Installation in a |
| |
1. Cut the foam seals(adhesive type) to the proper lengths and attach them |
| |
to the window and stool. (Fig. 10) | Foam seal A | |
2. Open the window sash and place the window slider kit on the window stool | ||
(adhesive type) | ||
(Fig. 11). Attach the window slider kit to the window stool. Adjust the length | ||
| ||
of the window slider kit according to the width of window. Screw down the |
| |
two screws on the window slider kit. See Fig.11. Cut the adjustable window | Fig. 10 | |
slider kit if the width of window is less than 26.6 inches (Fig. 12). | ||
| ||
3. Close the window sash securely against the window slider kit. (Fig. 13) | screws | |
4. Drive two 1/2" screws to secure the window slider kit to the window sash. | ||
(FIG. 13) |
| |
5. Secure the window slider kit to the window stool (FIG. 13): | Window slider kit | |
A: For wooden windows: Use 3/4" screws for securing. | ||
| ||
B: For |
|
6. To secure lower sash in place, attach right angle sash lock with | 26.6"~48.5" |
| |
ƎPPVFUHZDVVKRZQ),* |
|
| |
| Window stool |
| |
NOTE: It is difficult to lock the windows with the sash lock for | Fig. 11 | ||
windows, so you can use lock by window itself. |
|
|
|
7. Cut the foam seal to an appropriate length and seal the open gap | Cut this side to fit your window |
| |
between the top window sash and outer window sash, as shown in Fig.15. |
| ||
|
| ||
ļVFUHZV |
|
|
|
Window slider kit | Fig. 14 |
| Fig. 12 |
|
| ||
Foam seal | Fig. 15 |
| |
|
|
ļVFUHZVRUļ |
|
hex head cap screws | Fig. 13 |
Window stool | |
| Foam seal |
| (adhesive type) |
Installation in a sliding sash window |
1.Cut the foam seals(adhesive type) to the proper lengths and attach them to the window frame. See Fig.16.
2. | Open the window sash and place the window slider kit on the window stool. |
| Fig. 16 |
| See Fig.17. Attach the window slider kit to the window stool. Adjust the |
|
|
| length of the window slider kit according to the height of window. Screw | Window stool | Window slider kit |
| down the two screws on the window slider kit. See Fig.17. Cut the adjustable | ||
|
|
| |
| window slider kit if the height of window is less than 26.6 inches (Fig. 12). |
| screws |
3. | Close the sliding sash securely against the window slider kit. (Fig. 18) |
| |
4. Drive two 1/2" screws to secure the window slider kit to the window sash. |
|
| |
| (Fig. 18) | 26.6"~48.5" |
|
5. | Drive two 3/4" screws to secure the window slider kit to the window stool. |
|
|
| (Fig. 18) |
|
|
6. Cut the foam seal to an appropriate length and seal the open gap |
|
|
| Fig. 17 | |
between the sliding sash and outer window sash, as shown in Fig.19. |
|
|
|
| |
|
|
|
| ||
7. To secure the sliding sash in place, attach right angle sash lock with 1/2" |
|
|
|
| |
Window stool | Window slider kit | ||||
(12.7mm) screw as shown.(Fig.20) | |||||
|
|
|
| ||
|
|
|
|
| |
|
|
|
|
|
Foam seal ļVFUHZV
ļVFUHZV
Fig. 19 | Fig. 20 | Fig. 18 |
2009 Electrolux Home Products, Inc. | All rights reserved. | 7 | |
|
|
| |
|
|
|