Operating Instructions
Operating Instructions
NOTE
The following instructions represent the Control Panel, the same instructions can be used for the Remote Control.
COOLING MODE: In this mode the exhaust adaptor hose MUST be used.
1. Press the MODE button until the "Cool" indicator lights.
2. Press the " 
" Temp buttons for desired setting.
3. Press the FAN button for desired fan speed.
HEATING MODE: | In this mode you do not need to use the exhaust adaptor hose. | ||
(on some models) | 1. Press the MODE button until the "Heat" indicator lights. | ||
| 2. Press the " | " Temp buttons for the desired heat setting. | |
|
|
| |
DRY MODE: | In this mode you do not need to use the exhaust adaptor hose, BUT the water | ||
| collected must be discharged. See Drainage Section. | ||
| 1. Press the MODE button until the "Dry" indicator lights. | ||
| 2. The fan will run at low speed and the display will show the room temperature. | ||
| 3. Keep doors ＆ windows closed for best effect. | ||
|
|
| |
AUTO MODE: | Always have the exhaust hose attached in this mode. | ||
| When you set the air conditioner in AUTO mode, it will automatically select cooling, | ||
| heating(inapplicable for cooling only models), or fan only operation depending on what | ||
| temperature you have selected and the room temperature. The air conditioner will | ||
| control room temperature automatically round the temperature point set by you. Under | ||
| AUTO mode, you can not select the fan speed. | ||
|
|
| |
FAN MODE: | In this mode there is no need to use the exhaust hose or drainage hose. | ||
| However, if you require stale or smokey air to be removed from the room, | ||
| hook up the duct accessories as described in the "EXHAUSTING HOT AIR" | ||
| section. |
|
|
| 1. Press the MODE button until the "Fan" indicator lights. | ||
| 2. Press the FAN button to choose the desired fan speed. | ||
| 3. The fan will run at the selected speed and the display will show the room temperature. | ||
|
|
| |
TIMER OPERATION: | You can set both delay stop and delay start while unit is in ON position or OFF position. | ||
| When unit is in ON position, first press TIMER button to go to delay stop setting, then | ||
| “timer off” light will illuminate, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to | ||
| change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments | ||
| up to 24 hours. Then press the TIMER button to confirm the setting (the control will confirm | ||
| the setting automatically after 5 seconds) and go to delay start setting. Use the same way | ||
| as above to set the delay start timing. If you don’t need to set delay start, press the | ||
| TIMER button again to exit. After 5 seconds, the control will automatically change the | ||
| display back to previous temperature display. If you want to check remain timing, press the | ||
| TIMER button. The delay start operation automatically selects mode, temperature and | ||
| fan speed the same as last operation you set. | ||
| When unit is in OFF position, press TIMER button will first go to delay start setting, then | ||
| “timer on” light will illuminate, set the delay start and delay stop timing the same way | ||
| as above. |
|
|
| To cancel the timer setting, simply tap ( ) or ( ) button to change the timing to 0.0. | ||
|
|
| |
SLEEP OPERATION: | In this mode the selected temperature will increase by 2 °F 30 minutes after the mode | ||
| is selected. The temperature will then increase by another 2 °F after an additional 30 | ||
| minutes. This new temperature will be maintained for 7 hours before it returns to the | ||
| originally selected temperature. This ends the "Sleep" mode and the unit will continue to | ||
| operate as originally programmed. The "Sleep" mode program can be cancelled at any | ||
| time during operation by again pressing the "Sleep" button. | ||
| Note: This feature is unavailabe under FAN or DRY modes. | ||
2009 Electrolux Home Products, Inc. | All rights reserved. | 9 | |
|
|
| |
|
|
| |
