Frigidaire FGMO205KF Microwave Specifications, Optional Accessories, Frigidaire, Microwaves

Microwaves

FGMO205K F/ W/ B  Built-In

								30"min.**
	*Note: When used in combination with
	another Frigidaire® built-in product, a
	minimum clearance of 2 7/8" required from
	bottom of Built-In Microwave cutout to top
	edge of companion product’s faceplate,
	leaving a 2" visible gap between both							Full plywood
	product faceplates
								base required to
								support 100 lbs.
30"or 27"		Power cord
Trim Kit Faceplate		location (right			16 3/4"min.
	24 "	top rear)			17"max.		24 3/8"min.
							24 11/16"max.
18"		13	3	/8 "			20"
						2"	min.
				rear		(visible
				extrusion		gap)*
		19 1/8"						Trim Kit –
								7/8" faceplate
27"	1"							overlap
Allow at least
21" clearance for door
depth when open	120V/60Hz
	grounded outlet
Bottom Duct Assembly
		4"			6"
						Outlet should NOT
16 3/4"min.
						be located within
17"max.		4"				shaded area UNLESS		** Minimum cabinet width
						cabinet depth is
								required for installation
						greater than 21"
								with optional 30" Trim Kit.
24 3/8"min.								27" minimum cabinet width
			20" min.					required for installation
24	11/16"max.							with optional 27" Trim Kit.

Microwave Specifications

•Product Shipping Weight (Approx.) – 46 Lbs. (not incl. Trim Kit)

•Voltage Rating – 120V / 60 Hz / 15 or 20 Amps

•Connected Load (kW Rating) @ 120 Volts = 1.7 kW

(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)

•Amps @ 120 Volts = 14.3 Amps

•Always consult local and national electric codes.

•Microwave can stand alone on countertop or be built in with optional 30" or 27" Trim Kit (ordered by individual part number) which includes Bottom Duct Assembly – shipped in separate box.

•Allow 21" minimum clearance for 90° door swing.

•Minimum 20" deep oven cutout dimension is critical for proper installation for oven and faceplate to fit flush against cabinet front.

•Consult local building code, in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition.

•Full base of solid plywood or similar material required, capable of supporting 100 Lbs.

•Base must be level and front of cabinet square for proper operation.

•Grounded outlet should NOT be located in shaded area, as indicated, UNLESS cabinet depth is greater than 21".

•Can NOT be installed above any gas wall oven.

•Built-In Microwave is approved to be used in combination with any Frigidaire® Electric Single Wall Oven and /or Warmer Drawer. (Refer to model-specific Combination Installation Specification pages on web.)

•When used in combination with another Frigidaire® built-in product, a minimum clearance of 2-7/8" required from bottom of Built-In Microwave cutout to top edge of companion product’s faceplate, leaving a 2" visible gap between both product faceplates.

Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions

Optional Accessories

•30" Stainless Steel Trim Kit – (PN # MWTK30KF).

•27" Stainless Steel Trim Kit – (PN # MWTK27KF).

•30" White Trim Kit – (PN # MWTK30KW).

•27" White Trim Kit – (PN # MWTK27KW).

•30" Black Trim Kit – (PN # MWTK30KB).

•27" Black Trim Kit – (PN # MWTK27KB).

FRIGIDAIRE®

USA • 250 Bobby Jones Expressway • Martinez, GA 30907 • 1-800-FRIGIDAIRE • frigidaire.com	Specifications
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca	subject to change.

FGMO205K 05/09 © 2009 Electrolux Home Products, Inc. Printed in the U.S.A.