Frigidaire FRS26R4AQ1, FRS23KR4AB0, FRS26R4AW0 Installation - Connecting Ice Maker To Water Supply

Models: FRS23R4AB2 FRS23R4AQ2 FRS23R4AB0 FRS23R4AW1 FRS23R3AW1 FRS23R4AB1 FRS23R4AW0 FRS23R3AW0 FRS23R4AQ0 FRS23R4AW2 FRS23KR4AB1 FRS26KR4AB0 FRS26KR4AB1 FRS26KR4AW1 FRS26KR4AQ0 FRS26KR4AW0 FRS26KR4AQ1 FRS23KR4AW1 FRS23KR4AQ0 FRS23KR4AQ1 FRS23KR4AW0 FRS26R4AB1 FRS26R4AQ1 FRS26R4AB0 FRS26R4AQ0 FRS26R4AW1 FRS26R4AW0 FRS23KR4AB0

1 23
Download 23 pages 7.36 Kb
Page 5
Image 5
Installation - Connecting Ice Maker To Water Supply

Installation - Connecting Ice Maker To Water Supply

 To Avoid Property Damage:Before Installing The Water Supply Line, You Will NeedTo Connect Water Supply Line To Ice Maker Inlet ValveManual background To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.

Manual backgroundManual backgroundManual backgroundManual backgroundManual background To Avoid Property Damage:

Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any damage if plastic tubing is used for supply line.

DO NOT install water supply tubing in areas where temperatures fall below freezing.

Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

Access to a household cold water line with water pressure between 20 and 100 psi.

A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7.Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Page 5
Image 5
Frigidaire FRS26R4AQ1, FRS23KR4AB0 manual Installation - Connecting Ice Maker To Water Supply, To Avoid Property Damage