Frigidaire Tumble Action Washers warranty Doesnotfill, Softenercompartments

Models: Tumble Action Washers

1 14
Download 14 pages 29.53 Kb
Page 12
Image 12

 

CCURRENCE

POSSIBLECAUSE/SOLUTION

 

OPERATING

 

Washerdoesnotstart.

• Electrical power cord may not be plugged in or connection may be loose. Make

 

sure plug fits tightly in wall outlet.

 

 

• House fuse blown, circuit breaker tripped, or a power outage has occurred. Reset

 

 

circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit

 

 

overload, have it corrected by a qualified electrician. If problem is a power outage,

 

Washerwon'tspin.

call local electric company.

 

• Water supply faucets are not turned on. Turn on water supply faucets.

 

• Cycle selector is not in correct position. Move indicator clockwise slightly. Pull out

 

knob.

 

• Motor is overheated. Washer motor will stop if it becomes overheated. It will

 

automatically restart after a cool down period of up to 30 minutes (if washer has

 

not been manually turned off).

 

• Dispenser drawer is not completely closed. Close dispenser drawer.

 

• Washer door is not completely closed. Close door completely.

Washloadtoowetafterspin.

• Dispenser drawer is not completely closed. Close dispenser drawer.

• Washer is overloaded. Do not overload washer. See WashingProcedures.

Residueleftindrum.

• Load is too small. Add 1 or 2 similar items to help balance the load.

WATERatcollectsinblachandfabric

• Heavily soiled items. Wipe drum with a nonabrasive household cleanser, then rinse.

Shake or brush excess dirt and sand from items before washing.

• This is a result of the siphoning action and is part of the normal operation of the

 

softenercompartments.

washer. Water may be removed by removing the dispen er drawer (see Page 9,

Waterdoesnotenterwasherorit

Figures 1 and 2) and draining water into the empty drum or sink.

• Load is too small. Add 1 or 2 similar items to help balance the load.

• Load is out of balance. Rearrange load to allow proper spinning.

• Drain hose is kinked. Straighten drain hose.

• Water supply is not adequate in area. Check another faucet in the house. Wait until

entersslowly.

water supply and pressure increase.

 

 

• Water supply faucets are not completely open. Fully open hot and cold faucets.

 

 

• Water is being used elsewhere in the house. Water pressure must be at least 30

 

 

psi (260 kPa). Avoid running water elsewhere while washer is filling.

 

drinsslowly.

• Water inlet hoses are kinked. Straighten hoses.

 

• Hot water heater is set too low or is a distance from washer. Measure hot water

 

Warmorhotwaterisnothot

 

enough.

temperature at nearby faucet with candy or meat thermometer. Water temperature

 

inwasherdoesnotdrainor

should be at least 130°F (70°C). Adjust water heater as necessary.

 

• Hot water is being used elsewhere in the house. Avoid using hot water elsewhere

 

before or during washer use. There may not be enough hot water available for

 

proper cleaning. If problem persists, your hot water system may be unable to

 

support more than 1 use at a time.

 

• Drain hose is kinked or clogged. Clean and straighten the drain hose.

 

Waterleaks.

• Fill hose connection is loose at faucet or washer. Check and tighten hose

 

Incorrectwahandrinse

connections. Install rubber sealing washers provided.

 

• House drain pipes are clogged. Unclog drain pipes. Contact plumber if necessary.

 

• Oversudsing. Use less detergent.

 

• Hot and cold water hoses are connected to wrong supply faucets. Connect hot

 

temperature.s

water hose to hot water faucet and cold water hose to cold water faucet.

 

Waterisenteringwasherbuttub

 

 

 

• Drain hose standpipe is incorrect height. Standpipe must be a minimum of 23.6"

 

doesnotfill.

(60 cm) high to prevent siphoning. See INSTALLATION INSTRUCTIONS.

12

Page 12
Image 12
Frigidaire Tumble Action Washers warranty Doesnotfill, Softenercompartments, WATERatcollectsinblachandfabric