Deleting or Adding Channel, Automatic Clock Setting

AUTOMATIC CLOCK SETTING

Make sure ...

• The TV/VCR is turned on.

• Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

4Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the remote control.

system connection using the ANT IN jack on the

rear of the TV/VCR.

NOTE:

•If a cable converter box is being used, make sure it is powered on.

•You must use the TV/VCR remote control to per- form the clock setting procedure.

Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.

Press the F.FWD/B button to enter “SETTING CLOCK” menu. Press the STOP/L button to select “AUTO CLOCK CH”.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

–SETTING CLOCK –

1Select “SETTING CLOCK”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to select “SETTING CLOCK”. Press the F.FWD/B button to enter “SETTING CLOCK” menu.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

Press the F.FWD/B or REW/s	AUTO CLOCK	[ON]
Press the F.FWD/B or REW/s	B AUTO CLOCK CH	[ 45]
	AUTO CLOCK CH SEARCH
buttons until you locate Auto	MANUAL CLOCK SET
buttons until you locate Auto	D.S.T.	[OFF]

Clock Set station number. See item 3 above.

Press the MENU button to exit the screen.

5Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically check and set the correct date and time.

2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –
Press the F.FWD/B button until	B AUTO CLOCK	[ON]
AUTO CLOCK [ON] appears.	AUTO CLOCK CH SEARCH
AUTO CLOCK [ON] appears.	MANUAL CLOCK SET	[ ]
	AUTO CLOCK CH	[ ]
	D.S.T.	[OFF]

CHANNEL SET UP AGAIN

Make sure ...

•Press the POWER button to turn on the TV/VCR.

3Begin “AUTO CLOCK CH SEARCH”

1 Select “CHANNEL SET UP”

Press the MENU button on the

– M E N U –

Press the STOP/L button to select

“AUTO CLOCK CH SEARCH”. Press the F.FWD/B button.

• The TV/VCR is now searching

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

– SETTING CLOCK –

AUTO CLOCK

[ON]

BAUTO CLOCK CH SEARCH

AUTO CLOCK CH	[ ]
MANUAL CLOCK SET
D.S.T.	[OFF]

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

Then, press the F.FWD/B button.

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

BCHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

seconds per channel.

2Begin auto preset

– CHANNEL SET UP –

•“_ _” appears at the lower left of

the screen when the search has

ended.

• Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

– AUTO CLOCK CH SEARCH –

08 10 13

_ _

Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then, press the F.FWD/B button. The tuner scans and memorizes all the active channels in your area.

ADD / DELETE CH (TV)

BAUTO PRESET

4 below.

3After scanning

•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 11.

Press the MENU button to exit the screen.

The tuner stops on the lowest memorized channel.