Manuals / Brands / Marine Equipment / SONAR / Furuno / Marine Equipment / SONAR

Furuno CSH-23, CSH-23F, CSH-24, CSH-24F , Processor unit (right side, cover removed)

1 98

Download 98 pages, 4.17 Mb

J21

RGB port panel

Screw (4 pcs)

CONE board (10P6711)

Replace each

BCN connector

to the same

label port.

BNC connector

Processor unit (right side, cover removed)

Contents

Main Page i WARNING CAUTION SAFETY INSTRUCTIONS ii TABLE OF CONTENTS 5. CHANGING POWER SPECIFICATIONS......................................................34 1. SYSTEM CONFIGURATION STANDARD OPTION **: CSH-23/24 only. Figure 1-1 System configuration 2. EQUIPMENT LISTS 2a Optional Equipment 3. MOUNTING THE EQUIPMENT 3.1 Mounting the Hull Unit and Receiver Unit Location of hull unit Page Shortening the retraction tank Remarks for installation of retraction tank Installing hull unit on retraction tank Installing stays (anti-vibration measure) Fastening receiver unit to hull unit 3.2 Mounting the Display Unit/Sub-display Unit Mounting the display unit/sub-display unit 3.3 Mounting the Transmitter Unit 3.4 Mounting the Interface Unit 3.5 Mounting the FNZ Joint Box 3.6 Grounding the Equipment CAUTION Page 4.2 How to Use the Crimping Tool, Pin Extractor How to use the crimping tool How to use the pin extractor 4.3 Location of Connectors Figure 4-3 Location of connectors 15 4.4 Fabricating Cable, Assembling Connectors Fabricating cable 00-8016- 038-313-761HV (CN-A1, CN-A5 and J201) Shorten the unused wires appropriately and their ends with vinyl tape to prevent short circuit. Page Fabricating cable 54-038-000-601/SC (CN-E1) Assembling 38P connector Positioning guide pins Clamping the cable (side at power supply unit) Fabricating cable 10S1259 (connected terminal board TB-E1) Fabricating cable DPYCY-4 (connected to terminal board TB-E1) Fabricating cable 54-038-000-601/SC (CN-B2, CN-B3, CN-B4) Page Page Page 4.5 Connection of Transducer Cables 24 4.6 Connection of Interface Unit CS-120A Connections for true motion and target lock 26 Connections for ES picture and FNZ markers 27 Connections for digital indication of position, water temperature and depth Wiring Fabrication, assembling 10P and 7P connectors 3 mm Figure 4-30 Fabrication of 10P, 7P connectors 4.7 Connection of Sub-display Unit CSH-236/236F (Option) Connections DIP switch setting Page Page 4.9 Interlocking Operation with Other Sonar Connections for interlocking functions Two sonars Three sonars DIP switch setting Connections for interlocking remote control Page 6. ADJUSTMENT AND CHECK 6.1 Hull Unit Check 6.2 Heading Adjustment e 6.3 DIP Switch Setting in the Display Unit 38 6.4 Setting and Adjustment of the Interface Unit CS-120A -CIF: 47 ) to 470 Changed the register R78 (47 39 Interface unit (10P0047) adjustment 40 Priority for data Page 42 7. PROCESSOR UNIT CSH-235/235F (BLACKBOX TYPE FOR CSH-23/23F) 7.1 Installing the Unit 7.3 Connecting cables Protective earth CAUTION Connectors for Monitor Processor unit (right side, cover removed) Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 6 S-1 A CSH-21080/21120/21160 RECEIVER UNIT 100/110/220VAC Page Page 243 S-4 *2. OPTION. *1. SHIPYARD SUPPLY. NOTE VI-1100A