Furuno FI-50 Series specifications Basic Configurations, Easy to install, Sail Boat

System Configurations

Basic Configurations

Wind Transducer Wind Transducer

WIND CH WIND

FI-501 FI-502

DIGITAL

FI-503

MULTI

FI-504

COURSE PILOT RUDDER

FI-505FI-506

Easy to install

Surface Mount the displays with a hole saw then install 4 hidden screws under the front bezel. Installations are easy and clean with a finished appearance (1"(26mm)bulkhead protrusion)

Optional “Low Profile” Flush Mounting front panels provide a cosmetic match to NN3D Displays and a custom console appearance (0.4"(10mm)bulkhead protrusion)

Wind			Digital	Digital	Wind	Multi
	12 V		12 V				12 V
		Depth/Speed/Temp		Depth/Speed/Temp
		Sensor		Sensor

Sail Boat

Apparent and True Wind Angle is displayed	The FI-502 provides detailed and precise
in both analog and digital format when	wind bearing measurements from 60 port to
connected to the FI-5001 or other	60 Starboard, an important range for Close
NMEA2000® wind measurement system.	Hauled (CH) points of sail.

Data displayed

•Apparent and true wind speed •Apparent and true wind angle •Maximum true wind speed

•MAX/LOW true wind speed alarm •High/Low apparent wind angle alarm •Beaufort wind speed

•VMG to windward

The FI-503 displays critical digital data for navigation, such as depth, speed, temp, and atmospheric weather data in a 3-way split screen.

Data displayed

1	•Current depth •Shallow/deep alarm
	•Shallow/deep anchor alarm •Wind angle
	•High/Low apparent wind angle
2	•Boat speed •MAX/AVG STW •SOG •MAX/AVG
	SOG •VMG to windward •Wind speed •MAX
	true wind •MAX/LOW true wind speed alarm
	•Beaufort wind speed

The FI-504 features a large digital display. The combination of alpha and numeric characters present all of the data and functionality available in the FI-50 Network. Alternating Data Displays are possible and selected information can be switched at 3 second intervals.

Data displayed

•Displays all information on the FI-50 series

•NAVIGATION (Bearing/distance to WPT, XTE, WPT number/name, L/L, Satellites tracked, Roll & Pitch)

•ENVIRONMENT (Battery voltage, Time & Date)

The FI-505 provides a digital compass readout with an analog “Off-Course” needle that greatly assists the helmsman in maintaining the desired vessel course. Or, use the needle to check and verify the autopilot steering performance.

Data displayed

•Current heading •Locked heading

•Average heading •Course over ground

Connected to an Autopilot, the FI-506 Rudder Angle Display show precise rudder angle information.

Data displayed

•Rudder angle

Surface mount installation

Flush mount installation with optional front panel

	WAAS/GPS	Navnet 3D
Network Radar Sensor		Multi Function	Wind Transducer
	Antenna	Display

		Digital	Wind	Multi	CH Wind
	Junction Box
Depth/Speed/Temp
			* 12V power will be supplied from NavNet 3D
Sensor

3 •LOG •Trip •Count up/down timer •Water

temperature •Air temperature •Air pressure

•Humidity •Wind chill temperature •Dew point

•ENGINE (Trip fuel used, Fuel consumption, Engine RPM)

Specifications of FI-50 series

Display:	Analog and digital LCD (FI-501, 502, 505)
	Digital LCD (FI-503, 504)
	Analog (FI-506)
Power supply:	12 VDC, less than 0.1 A
Temperature:	–15°C to +55°C
Waterproofing:	IP56

Sensors and Accessories (Option)

Wind Transducer

The units are designed to match the	Wind Transducer
NavNet 3D series and other navigation
equipment. The “Plug and Play” system
utilizes NMEA 2000® interface protocol,
which gives the system exceptional
interface ability.

FI-501	FI-503	MULTI FUNCTION
		DISPLAY

JUNCTION

BOX

Easy to Read with Silver Bright LCD Display

Power Boat

	WAAS/GPS	Navnet 3D
Network Radar Sensor		Multi Function	Wind Transducer
	Antenna	Display

FI-5001

Angle Accuracy:	Better than ±10°
Speed Accuracy:	Better than ±5 % (20 kt)
Power supply:	12 VDC, less than 40 mA
Transducer cable:	30/50 m

Depth/Speed/Temp Sensor

DST-800

Frequency: 235 kHz

The FI-50 Series utilize high-contrast, backlit LCD displays for superior viewing even in direct sunlight. Each unit features an easy-to-read display and 4 simple programming buttons for operation. The function for each key and combination is printed directly on the front panel.

FI-503 DIGITAL	FI-504 MULTI
22mm

Automatic Backlight Adjustment

The FI-50 series of instruments minimize power consumption by turning off the backlight during the daytime. Sensors on the front panel measure ambient lighting conditions and adjust the on/off condition of the display backlighting accordingly.

Daytime Sunset or after

		Digital	Wind
HUB
	Depth/Speed/Temp	Junction Box
DFF1	Sensor
Transducer		* 12V power will be supplied from NavNet 3D

Multi

NMEA 2000® NMEA 0183 Ethernet others

Junction Box

FI-5002

NMEA2000® backbone x 2 ports NMEA2000® x 6 ports

Power supply: 12 VDC, less than 2 A

22mm
	41mm

Back Light

Turns On

Automatic Detection

Back Light

Turns Off

Operational guide description on the front panel