AMPLIFIER SPECIFICATIONS
|
|
|
| |
|
|
|
| |
Peak Power (Watts) | 2250 | 1400 | 1600 | |
|
|
|
| |
Frequency Response | 10Hz - 250Hz | 10Hz | 10Hz | |
|
|
|
| |
Dimensions (mm) | 300(l) x 210(w) x 50(h) | 300(l) x 210(w) x 50(h) | 300(l) x 210(w) x 50(h) | |
| ||||
|
|
|
| |
| 500W RMS x 1 @ 4Ω 1% | 150W RMS x 4 @ 4Ω 1% | 80W RMS x 4 + | |
| 250W RMS x 1 @ 4Ω 1% | |||
| THD+N | THD+N | ||
| THD+N | |||
|
|
| ||
|
|
|
| |
| 850W RMS x 1 @ 2Ω 1% | 220W RMS x 4 @ 2Ω 1% | 130W RMS x 4 + | |
Power Ratings | 330W RMS x 1 @ 2Ω 1% | |||
THD+N | THD+N | |||
THD+N | ||||
|
|
| ||
|
|
|
| |
|
|
| 250W RMS x 2 @ 4Ω | |
| 1100W RMS x 1 @ 1Ω 1% | 440W RMS x 2 @ 4Ω | Bridged 1% THD+N + | |
| THD+N | Bridged 1% THD+N | 250W RMS x 1 @ 4Ω 1% | |
|
|
| THD+N | |
|
|
|
|
INSTALLATION GUIDELINES
1.Ensure the +12V lead is disconnected from the battery before you connect any new equipment.
2.Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.
3.Ensure the Amplifier is securely fastened to the vehicle to prevent injury in the event of an accident.
4.Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.
5.Ensure the mounting location has sufficient air flow around the amplifier. If the amplifier is mounted in an enclosed space a 3” fan with ducting should be used to aid in air flow.
6.Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the amplifier.
7.Ensure you use the recommended gauge wire/cable for all amplifier connections.
POWER
FUSION amplifiers should be connected directly to the +12V battery terminal with an inline fuse or circuit breaker as close the battery as possible.
GROUND
When grounding/earthing your amplifier ensure that the location is a good source of ground (preferably the floor pan). Make sure the metal is clean of paint etc as a poor earth could damage your audio system.
REMOTE TURN ON
This connection turns the amplifier on & should be connected to the remote turn on wire from the Head Unit. If one is not available a switched 12v source must be used. Either a power antenna wire or ACC +12V.
LOW LEVEL INPUTS
WIRING
1.Ensure the audio system is turned off before making any connections to the amplifier, speakers or source unit, failure to do so could result in permanent damage to the audio system.
2.When wiring the FUSION amplifier ensure that the cable is protected from sharp objects and always use rubber grommets when wiring through metal panels.
3.Ensure all terminals and connections are protected from the vehicle chassis and from each other as failure to do so could result in permanent damage to the audio system.
Choose the correct length RCA cable & run them to the RCA outputs of the source/head unit, avoiding running beside other looms & or power cable.
For specific wiring information please refer to www.fusionelectronics.com
