8” SUPER SLIM ACTIVE SUBWOOFER

CP-AS1080

SPECIFICATIONS

 

CP-AS1080

Peak Power (Watts)

300

Rated Power (Watts)

100

Frequency Response

20Hz - 120Hz

Dimensions (mm)

330(l) x 245(w) x 78(h)

 

13 x 9-5/8 x 3”

INSTALLATION GUIDELINES

1.Ensure the +12V lead is disconnected from the battery before you connect any new equipment.

2.Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.

3.Ensure the Super Slim Active Subwoofer is securely fastened to the vehicle to prevent damage in the event of an accident.

4.Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.

5.Ensure the mounting location has sufficient air flow around the amplifier.

6.Ensure you use the recommended gauge wire/cable for all amplifier connections.

WIRING

Ensure the audio system is turned off before making any connections to the amplifier, speakers or source unit.

Failure to do so could result in permanent damage to the audio system. When wiring the FUSION Super Slim Active Subwoofer ensure that the cable is protected from sharp objects and always use rubber grommets when wiring through metal panels.

Ensure all terminals and connections are protected from the vehicle chassis, and from each other, as failure to do so could result in permanent damage to the audio system.

FUSION Electronics recommends 8 gauge wire (power & ground).

POWER

Connect the power lead directly to the +12V battery terminal with an inline fuse or circuit breaker as close to the battery as possible.

LOW LEVEL INPUTS

Choose the correct length RCA interconnects and run them to the RCA outputs of the source/head unit, avoiding running beside other looms and or power cable.

Note: For correct performance both input RCA connectors must be used.

GROUND

When grounding/earthing your Super Slim Active Subwoofer ensure that the location is a good source of ground (preferably the floor pan). Make sure the metal is clean of paint etc as a poor earth could damage your audio system.

Note: This is the first connection to be made!!

REMOTE TURN ON

This connection turns the amplifier on and should be connected to the remote turn on wire from the Head Unit. If one is not available a switched 12V source must be used. Either a power antenna wire or ACC +12V.

HIGH LEVEL INPUTS (SPEAKER LEVEL)

If your head unit does not have RCA outputs, you can use the speaker outputs for the audio source for the CP-AS1080. Use the supplied cable and wire harness and connect the speaker outputs from the source to the high level Input. Be sure to observe polarity to avoid audio phase problems.

Note: When using the high level connection, the Level MUST be set to minimum or the Subwoofer will be permanently damaged and could void your warranty.

LOW LEVEL OUTPUTS

Use the RCA output connectors to make one CP-AS1080 linkable to multiple CP-AS1080 Super Slim Active Subwoofers. This output is a pass-thru connection derived from the RCA input connector so the signal level and frequency response is the same as the original input signal.

www.fusionelectronics.com

Page 1 Page 2
Page 1
Image 1
Fusion CP-AS1080 specifications Specifications, Installation Guidelines, Wiring, Power, LOW Level Inputs, Ground
Page 1 Page 2

CP-AS1080 specifications

The Fusion CP-AS1080 is an advanced audio amplifier designed to meet the requirements of professional audio systems. With its sleek and robust design, the CP-AS1080 is an ideal choice for both live sound applications and installed audio setups. This amplifier boasts a variety of features and technologies that make it stand out in the crowded audio market.

At the heart of the CP-AS1080 is its impressive power output. Delivering up to 1080 watts of dynamic power across its channels, this amplifier is capable of driving a wide range of speaker systems, ensuring that the sound produced is loud, clear, and distortion-free. The amplifier operates efficiently across various impedances, making it versatile enough to handle different configurations, from low-impedance loads to higher impedance setups.

One of the standout technological features of the CP-AS1080 is its Class D amplification technology. This allows for higher power output with less heat generation compared to traditional Class AB amplifiers. As a result, the CP-AS1080 is more energy-efficient, which not only reduces operational costs but also extends the lifespan of the unit. The Class D design also contributes to a lighter weight, making it easy to transport and install.

The amplifier is equipped with a built-in DSP (Digital Signal Processing) engine that provides users with advanced audio processing capabilities. This DSP functionality includes various preset EQ settings, crossover controls, and limiter settings that enable precise tailoring of the audio output. Users can adapt the sound to suit specific environments or preferences, ensuring optimal performance in any scenario.

In terms of connectivity, the CP-AS1080 offers multiple inputs and outputs, including XLR and TRS connectors, making it compatible with a wide range of audio sources. The rear panel features adjustable gain controls and signal indicators, allowing for straightforward setup and monitoring.

Another notable attribute of the CP-AS1080 is its robust thermal management system. Designed with internal cooling fans and efficient heat sinks, this amplifier ensures that it can operate consistently, even during long sessions or in warm environments. With over-temperature protection features in place, users can trust that the device will remain reliable and safe during operation.

Overall, the Fusion CP-AS1080 is a powerful, efficient, and versatile amplifier that incorporates cutting-edge technologies and thoughtful features, making it a compelling choice for any audio professional seeking high-quality performance in various applications.
Top Page Image Contents