Gardena RM330 manual GARDENA Accu Cordless Motor Mower RM, Technical Data, Product Use

G

GARDENA Accu Cordless Motor Mower RM 380

K Plug for charger

L Charging socket in housing

Note: Make sure that the groove in the drilled hole and

G

4.5Setting the Cutting Height (Fig. D / D1)

1. Technical Data

Accu

Design

Voltage/capacity

Weight

Cordless Motor Mower Width of the cutting cylinder Weight

Working area related emission characteristic value L pA 1)

Noise level	L WA 2)
Vibrations	a vhw 1)

maintenance-free lead battery 12 V / 7.2 Ah

approx. 2.4 kg

38cm approx. 12 kg

70 dB (A)

84 dB (A)	Measuring method acording to
< 2.5 ms - 2	1) EN 836 2) directive 2000/14/EC

M Mains plug for charger

N Turning knob for Accu cover

O Receptacle for tabs

P Tabs on Accu

Q Key

R Thickness gauge

S Hexagon thread bolt

(to adjust cutting tool)

4.3 Assembling the Guide

Handle (Fig. A/B/C)

Assemble the guide handle as

follows:

1. Guide the upper section of

the guide handle 3 into the

grooves of the two middle

sections of the guide handle 4

the safety pin of the handle bolt A meet.

Warning! Do not use exces- sive force. First ensure that the opening 0 and bolt A are aligned and then fix together.

4.4 Assembling the Starting

Device (Fig. C 2 - C 4)

To assemble the starting device,

both holes (a) must be on your

right hand side when standing

behind the mower (in the direc-

tion of movement).

1. Pull open the clamps (b) of the

starting device (15a) (Fig. C2).

Warning! To prevent Ainjury, never set the cut- ting height when the motor is running.

Set the cutting height on the Accu Cordless Motor Mower as follows:

1.	Stand the Accu Cordless Motor
	Mower on a flat, solid surface.
2.	Position yourself in front of the
	cutting height scale of the Cord-
	less Motor Mower (Fig. D1).
3.	Loosen both fixing nuts 9
	(Fig. D).
4.	With both hands on the adjust-
	ing handles B set the cutting
	height you require (Fig. D1):

2. Operating Instructions Information

Please read and follow these	For safety reasons chil-
operating instructions carefully.	Adren under the age of
Familiarise yourself with the unit’s	16 or people not familiar with
features, its proper use and the	these operating instructions
safety instructions included.

must not use this Accu Cord- less Motor Mower.

Please keep these instructions in a safe place.

	(Fig. B)
2.	Screw the upper section 3
	to both middle sections of the
	guide handle 4 using the bolts
	and wing nuts provided 6.
3.	Guide the lower part of the
	guide handle 5 into the
	grooves of the middle sections
	of the guide handle 4 (Fig. B)

2. Guide the two pin receptacles

(c) of the lower clamp into the

holes (a) and

3. insert the two pins (d) of the
	upper clamp into the holes
	(Fig. C 3).
4.	Press the two clamps back
	together.
5.	Screw the assembled clamps

Highest cutting height: 45 mm

Lowest cutting height: 20 mm

Note: Make sure that the

arrows marking the cutting

height 8 show the same

cutting height on both sides

of the scale (Fig. D 2).

5. Re-tighten both fixing nuts 9

(Fig. D).

3. Product Use

The GARDENA Accu Cordless Motor Mower RM 380 is designed for cutting and aerating lawns in and around the garden.

It is not designed for use in public facilities, parks, sporting grounds, on roads, in agriculture or forestry.

It is essential to observe the manufacturer’s operating instruc- tions to ensure the unit’s proper functioning. The operating instruc- tions also contain advice for service, maintenance and repair.

Attention! To prevent

for trimming bushes, hedges, shrubs, for cutting and pruning of climbers or grass on roofs or in balcony boxes.

Attention! For risks of in- Ajury the Accu must not be used as power source for other

and screw together with the

bolts and wing nuts provided 6.

4. Push both sides of the guide

handle with the opening 0

over the handle bolts A as

shown in Fig. C1.

onto the guide handle using

the two Phillips screws provid-

ed (Fig. C 4).

6. Secure the cable to the handle

using the cable clips 7.

Warning! The cable must not

hang down near the cutting

cylinder.

Note: When setting the Cord-

less Motor Mower to a low

cutting height, ensure that

the lower blade and cutting

cylinder do not touch the

ground if the ground is

uneven.

Ainjury, the Accu Cordless

Motor Mower must not be used

devices.

5. Putting into Operation

4. Assembling the Accu Cordless Motor Mower

4.1 Checking all Parts are	. 1 key (battery compartment)	7 Cable clip
Included	. 1 Accu charger	8 Cutting height marking arrows
The Accu Cordless Motor Mower	. 1 thickness gauge	9 Fixing nuts
box contains the following parts:	. Operating instructions	0 Opening for snug and
. Cordless Motor mower	4.2 Operating Parts	handle bolts
. 1 Accu		A Handle bolts
. 1 upper section of the guide	1 Cutting cylinder	B Adjusting handles
handle	2 Lower blade	C Cover for the Accu
. 1 lower section of the guide	3 Upper section of the guide	D Release knob
handle	handle	E Starting handle
. 2 middle sections of the guide	4 Middle sections of the guide	F Grass catcher
handle	handle	G Grass catcher holders
. Assembly parts for the guide	5 Lower section of the guide	H Hooks for grass catcher
handle (plastic bag)	handle	I Accu
	6 Wing nuts with bolts	J Charger

5.1Preparation for Initial Operation (Fig. E) Assemble the Accu I as de- scribed in section 7.2 „The Accu

– Changing the Accu“.

Note: the Accu is charged at the factory but may loose its capacity if it has been stored for a long time. If the Accu is flat when you purchase your Cordless Motor Mower or immediately after use, you must recharge the Accu as described in section “Charging the Accu”.

5.2Starting your Mower (Fig. A/E)

Warning! Before starting your Cordless Motor Mower check for foreign bodies in the cutting cylinder and remove if neces- sary.

Start your Cordless Motor Mower as follows:

1.Stand your mower on a level part of the lawn.

2.Open the accu cover N.

3.Insert the key Q (supplied in the battery compartment) the right way round into the socket of the Motor Mower (Fig. E).

4.Close the accu cover.

5.To start the motor, press and hold down the release knob D and with the other hand, simul- taneously pull the starting han- dle E towards the cross bar (Fig. A).

6.If you release the starting handle E the motor switches off again.

Important! Always keep the accu cover closed when work- ing with the Motor Mower!

The switches installed Aby the manufacturer must not be removed or be bridged eg: by taping down the starting handle E to the guide handle.

16 17