ASSEMBLY INSTRUCTIONS CONT.
Step 4: Align the flat of the shaft with the securing screw on the fan blade and slide the fan blade onto the shaft with the securing screw facing the rear grill.
Step 5: Center the front grill by aligning the GE Brand logo on the logo plate so it is upright and straight. Then, holding the front grill against the rear grill snap each clip forward onto the front grill.
Final Assembly
Step 1: First, slide the inner pole up from the outer pole. Insert the Pole Lock Knob into the hole on the outer pole, to securely hold this position. Next, place the fan head assembly into the inner pole, inserting the neck of the fan into the pole open ing. Turn the fan head’s neck until the head is securely locked into place. Finally, add the Tilt Adjustment Knob to the hole of the fan head’s neck. Tighten when fan head is in the desired position.
OPERATING INSTRUCTIONS
Step 1: Set the fan base on a dry, level surface.
Step 2: Please make sure the On/Speed switch is in the "Off" position. Plug the cord into any standard
Step 3: The SPEED is adjusted by moving the switch left
or | right to the desired setting. |
| |||
Step 4: The OSCILLATION knob is located on | |||||
| the top of the fan motor housing. To start oscilla- | ||||
| tion, push control knob down. To stop oscillation, | ||||
| pull control knob up. |
|
| ||
|
|
| C | Q | |
|
|
| G | ||
|
|
|
| ||
|
|
|
| H | |
A.) Front Grill |
|
|
| ||
B.) Fan Blade |
| D | I | ||
C.) Securing Screw |
| ||||
|
| F | |||
D.) Rear Grill |
|
| |||
|
| J | |||
E.) Rear Grill | A | B | |||
F.) | Motor Shaft | E | |||
|
| ||||
G.) Motor Housing |
|
| K | ||
H.) Tilt Adjustment Knob |
|
| |||
|
| L | |||
I.) | Inner Pole |
|
| ||
J.) | Pole Lock Knob |
|
|
| |
K.) Outer Pole |
|
| M | ||
L.) Pole Ring |
|
|
| ||
M.)Base |
|
|
| ||
N.) Weighted Insert |
|
| N | ||
O.) Washer |
|
| |||
P.) | L Shaped Locking Lever |
|
| O | |
Q.) Grill Clips (6) |
|
| |||
|
| P | |||
|
|
|
|
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment
Step 1: To change the tilting angle of the fan head, sim- ply loosen the Tilt Adjustment Knob.
Step 2: Move the fan head to the desired angle, and then firmly tighten the knob to lock the fan head in place.
Height Adjustment
Step 1: Turn the Pole Lock Knob counter clockwise to loosen the inner pole.
Step 2: Adjust the inner pole to the desired height, and firmly tighten the pole lock knob in a clockwise direction.
WARNING: Make sure to support the fan head assembly when loosening the adjustable height knob, as the weight of the fan head may cause the inner pole to collapse.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for your GE Brand stand fan. Please remember:
•Always unplug the fan before cleaning or disassem- bling.
•Do not allow water to drip on or into the fan motor housing.
•Do not use any of the following as a cleaner: gasoline, thinner, benzine.
(See instructions for fan head assembly)
Step 1: To access the fan blade, remove the front grill and then unscrew the securing screw on the fan blade.
Step 2: Clean the fan blade, both front and rear grills with a soft cloth moistened with a mild soap solu- tion.
Step 3: Replace blade, tighten the fan blade by screwing the fan blade back on, and securely fasten the front grill.
Fan Head, Base, and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap solu- tion, carefully clean the fan base, pole, and head. Please use caution around the motor housing area. Do not allow the motor or other electrical components to be exposed to water.
FAN STORAGE
Your fan can be stored in the
•If stored disassembled, we recommend using the origi- nal (or appropriately sized) box.
•If stored assembled or partially assembled, remember to protect the fan head from dust.