GE Model 19216

www.jascoproducts.com

Wireless Door Chime Kit

Installation Instructions AC Wireless Chime Kit

Required Tools: Small flat blade screwdriver, drill, 1/16” drill bit, and phillips screwdriver.

Included Hardware:

(2) 3x20mm screws

(1) Double sided adhesive pad

The wireless door chime kit has two components:

Chime (Receiver)

Battery Operated

PushButton (Transmitter)

Plugs into 120V outlet

Battery included

Chime Tune Setting

All wireless chimes may have more than one push button. The chime tune for each push button is set with dip switches 1-3. Located inside the push button.

Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory.

Dual Push Button Kit: If you purchased a kit with two push buttons, one push button will be set to Ding Dong and the other push button will be set to Westminster from the factory.

The following instructions explain how to change the tune on any wireless push button.

1.Remove the cover from the push button - see wireless push button battery.

2.Remove the battery from the push button transmitter.

3.Locate the 3 dip switches shown below.

4.Select the desired chime sound from the table below.

Chime Sound Table

1

2

3

Position

Westminster

ON

OFF

OFF

Ding Dong

OFF

ON

OFF

Knock

OFF

OFF

ON

Bronze Chime

ON

ON

OFF

Cuckoo Clock

ON

OFF

ON

Foghorn

OFF

ON

ON

Gong

ON

ON

ON

Pushbutton House Code Jumpers

Chime Dip Switches

Setting The House Security Code

Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code. If your chime activates intermittently or does not work at all, you may be able to solve the problem by changing your security code.

Pushbutton

House Code

Jumpers

Chime Dip

Switches

The chime and pushbutton must be set to the same house security code for the combination to operate together.

1.Remove power from the chime.

2.To remove the batteries from the pushbutton, open the pushbutton case as shown below.

Pushbutton

House Code

Jumpers

Chime Dip

Switches

4.Locate the chime and pushbutton jumpers shown above.

5.To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. The jumpers on the chime and pushbutton must match exactly.

Wireless push button battery

To install or replace the battery in the wireless push button.

1.Remove the back cover of the push button.

2.Install the A23 (12 volt) battery with the negative side of the battery (-) toward the spring and the positive side of the battery (+) toward the positive battery holder as shown below.

3.Replace back cover as shown below.

Push Button Mounting Instructions

Note: Avoid mounting on metal surfaces, as it may result in a reduced range of transmission. Do not mount in an area where exposed to direct rain.

a. Removing the back cover

b. Replacing the back cover

2.Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location.

Not further than 150 feet

3.Before placing the pushbutton where you would like to mount it, place the chime as close to final position as possible. Test the operation before drilling. If it works, mount the push button. If it does not work, see TROUBLESHOOTING.

4.Use back cover of push button as a template to mark two screw holes.

4

5

6

8

5. Drill two holes with 1/16” size drill in marked locations.

6. Secure back cover to the mounting surface with two supplied mounting screws.

7. Install the supplied 12V battery observing proper polarity. (see battery installation section)

8. Press front housing onto back cover.

9. Test operation. If the chime does not work, see

TROUBLESHOOTING.

If you do not want to drill holes in your door frame, you can use the supplied double sided tape for installation.

1. Clean all mounting surfaces with a 50/50 mixture of isopropyl alcohol.

2. Remove the backing from one side of the double sided tape and press the exposed side against the back plate of the push button.

3. Remove the other backing strip and press the exposed side against the door frame where you want the button installed.

Power Indicator

2.Gently press transmitter button to sound chime.

Troubleshooting

Chime doesn’t work:

1. Make sure push button switch is depressed and held for at least 1 second.

2. Make sure house code switches 1-4 on chime and push button match exactly.

3. Verify battery orientation in push button.

4. Try fresh batteries.

5. Make sure chime is not farther than 150 feet away from push button.

6. Ensure push button is not mounted on metal, near metal studs, or near the floor.

7. Try a new location for the chime.

Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery and obstructions between the transmitter and receiver.

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept interference received, including any interference that may cause undesired operation.

For technical support contact Jasco Products Company at 1-800-654-8483

or www.jascoproducts.com

Made in China

is a trademark of General Electric Company

and is used under license to Jasco Products Company LLC,

10 E. Memorial Rd., Oklahoma City, OK 73114. www.jascoproducts.com

Rev. 10-07

19216

 

Pushbutton Jumpers

 

3. Locate the House Security Code door and screw

Pushbutton Dip Switches and Jumpers

located on the back of the Chime. Remove the

screw and take off the door.

 

Mounting Push Button

1. Push buttons are typically mounted at the same height as the door knob or handle (between 36” and 44” above the floor).

On/Off Switch

Operation

1.Plug the chime into a 120V AC outlet and slide the power switch to the “On” position to turn on the chime. The red LED power indicator will light.

Page 1
Image 1
GE 19216 installation instructions Installation Instructions AC Wireless Chime Kit, Included Hardware, Chime Tune Setting

19216 specifications

The GE 19216 is an innovative and robust electrical distribution transformer designed for efficiency and reliability in various applications. Built with advanced engineering techniques, the GE 19216 aims to deliver superior performance in both urban and industrial settings.

One of the main features of the GE 19216 is its high-efficiency design. The transformer incorporates amorphous steel core technology, which significantly reduces energy losses during operation. By minimizing these losses, the GE 19216 not only enhances operational performance but also contributes positively to energy conservation efforts. This feature is particularly beneficial in areas with high load demands, ensuring that energy supply remains stable and efficient.

Another notable characteristic of the GE 19216 is its compact design, which allows for installation in tight spaces without compromising performance. The transformer’s modular construction provides flexibility in adapting to different setups, making it suitable for both retrofitting existing infrastructure and new construction projects. This versatility is essential for modern electrical grids that require dynamic responses to changing load patterns.

In terms of technologies, the GE 19216 employs state-of-the-art monitoring systems that enable real-time data collection and analysis. These smart monitoring capabilities facilitate predictive maintenance, reducing unexpected downtime and lowering maintenance costs. Operators can easily access performance metrics via an intuitive interface, allowing for quick decision-making and efficient resource management.

Additionally, the GE 19216 transformer is designed with enhanced safety features. Robust insulation materials and dual grounding systems enhance the safety of operations, minimizing risks associated with electrical failures. This safety-first approach is crucial in high-stakes environments, ensuring both equipment longevity and operator safety.

Overall, the GE 19216 stands out for its energy efficiency, compact design, advanced monitoring technologies, and commitment to safety. Whether utilized in commercial buildings, industrial plants, or renewable energy facilities, this transformer is engineered to meet the demanding needs of contemporary electrical distribution networks. With its combination of innovative features and reliable performance, the GE 19216 is a valuable asset for utilities and enterprises looking to optimize their power distribution systems.