Manuals / GE / Household Appliance / Dehumidifier

GE ADEHSO, ADERSO warranty About the controlson the dehumidifier, Fan Speed Pad, Delay Off

Models: ADERSO ADEHSO

1 36
Download 36 pages 39.96 Kb
Page 4
Image 4

About the controlson the dehumidifier.

4 houror2 hour

High,Medium

Cleanthe Filter

Continuousoperationon

BucketFulllightindicates

delayoff

andLowfan

indicatorlight

indicatorlight

bucketneedsto beemptied

indicatorlights

indicatorlights

 

 

oris not inplaceinthe unit

 

Humidity %

4 hour

High

 

 

Mediul

2 hour

Low

 

NOTE:When the bucket is full or removed, the

controls cGnnot be set.

Controls

OPower Pad

Pressto turn the dehumidifier on and off.

OFiiter Timer

After 250 hours of operation,the Cleanthe Filter

indicator light will glow to remind you to clean the filter. Removethe filter and clean it.

Pressto turn off the Cleanthe Filterlight.See the Careand Cleaningsection.

@Humidity Set Control Pads

The humidity level can be set within a range of 35% RH(RelativeHumidity)to 80% RH(Relative Humidity) in 5% increments or at COlor continuous operation. To set the unit for continuous operation, pressthe T pad until the screen reads CO.

NOTE:If CO(Continuous)is selected,the dehumidifier will operate continuously at its maximum dehumidification settings if attached to a hose to drain or until the bucket isfull.

Fordrier air, pressthe V pad and set to a lower percent value (%).

Fordamper air, pressthe A pad and set to a higher percent value (%).

o-

e,

 

]

Continuous

Bucket

Full

 

 

 

PowerOn

Clean the Filter

Power

On

indicatorlight

When you first use the dehumidifier, set

the humidity control to 45% or 50%. Allow at least 24 hours for the dehumidifier to achieve

the humidity level. Ifyou still have damper air than desired,set the humidity level to a lower

setting or select Continuous for maximum dehumidification.

Shows the set % humidity level while setting, then shows the actual (+/- 5% accuracy) room % humidity level.

0 Fan Speed Pad

Controls the fan speed.

Pressto select either High,Medium or Lewfan speed.

Set the fan control to Highfor maximum moisture removal. When the humidity has been reduced and quiet operation is preferred, set the fan control to Medium or Low.

O Delay Off

While the dehumidifier is in operation, press this pad to set it to automatically turn off in 2 hours or/4 hours.

OtherFeatures

BUCKETFULLLight

Glowswhen the bucket is ready to be emptied, or when the bucket is removed or not replaced in the proper position.

Alarm

Ifthe bucket isfull or missingfor more than 3 minutes,an alarm will sound for about 10seconds to remindyou to empty and replacethe bucket.

AutoShutOff

4The Water LevelControl Switch shuts off the dehumidifier when the bucket isfull, or when

the bucket is removed or not replaced in the proper position. NOTE: Fan will continue to run approximately 3 minutes after bucket is removed.

AutoDefrost

When frost builds up on the evaporator coils,the compressor will cycle off and the fan will continue to run until the frost disappears.

Power Outage

In the case of a power outage or interruption, the unit will automatically restart, in the settings last used,after the power is restored.

Page 3 Page 5
Page 4
Image 4
GE ADEHSO, ADERSO warranty About the controlson the dehumidifier, Fan Speed Pad, Delay Off
Page 3 Page 5

ADERSO, ADEHSO specifications

GE ADEHSO (Advanced Electrical High-Density Switching Optimization) and ADERSO (Advanced Distributed Energy Resource Switching Optimization) are cutting-edge technologies developed by General Electric to address the evolving challenges in energy management and distribution. These systems are specifically designed to enhance the efficiency, reliability, and performance of electrical grids, particularly in a landscape where renewable energy and distributed generation sources are becoming more prevalent.

One of the main features of GE ADEHSO is its ability to optimize the switching operations in high-density electrical networks. It utilizes advanced algorithms and machine learning techniques to analyze real-time load conditions, allowing for dynamic reconfiguration of the network. This capability not only enhances the resilience of the grid but also minimizes downtime and enhances service reliability, thereby reducing operational costs for utilities.

ADERSO complements ADEHSO by focusing on distributed energy resources (DERs). With the increasing integration of solar panels, wind turbines, and battery storage systems, the need for sophisticated management of these resources has never been more critical. ADERSO provides a comprehensive framework for coordinating and optimizing DERs to ensure that they are utilized effectively while maintaining grid stability. It facilitates peer-to-peer energy trading and enhances demand response initiatives, contributing to a greener energy landscape.

Both ADEHSO and ADERSO utilize the Internet of Things (IoT) technologies to create smart grid systems. By leveraging IoT sensors and devices, these systems can gather and process data from various sources, providing utilities with unprecedented insights into grid operations. This data-driven approach allows for proactive maintenance and quicker response to potential outages or system failures.

In terms of characteristics, GE ADEHSO and ADERSO are designed to be scalable and adaptable. They can be integrated into existing grid infrastructures without significant overhauls, making them suitable for a wide range of applications—from urban centers to remote areas. Furthermore, their user-friendly interfaces allow operators to easily interact with the systems, facilitating intuitive management of complex energy networks.

In summary, GE ADEHSO and ADERSO represent a significant advancement in energy distribution and management technologies. By enhancing switching operations and optimizing the integration of distributed energy resources, these systems not only improve grid reliability but also play a crucial role in advancing the global transition towards sustainable energy sources.